0
What else can I help you with?
What liquid would you use in the electroplating bath to coat zinc with copper?
copper sulphate solution
What would happen if you poured 20cm cubed blue copper sulphate solution into a dish and left it at 21 celsius for two days?
u would get a blue waffle
What will happen if copper metal is added to iron sulfate solution?
nothing will happen as i have done this experiment. I think it is because iron is more reactive than copper, so the copper can't take away the sulphate. but if you added the iron to a copper sulphate solution the product would be iron sulphate this reaction is called displacment. David corrected by hari
We are using 5 percent solution of copper sulphate processing 140 ton per hour and consume 885 gm of copper sulphate per 1 ton of ore. what would be the usage of copper sulphate in liters per hour?
885x140=123900grams of copper sulphate per hour. If you are talking about using 885 gm of copper sulphate per ton of ore in the solution then the density of the copper sulphate(penta hydrate now because it's in water) is 2.284 gm per cm3 so that's 2.284x5=11.42gm per liter of solution, so 123900/11.42=10849.387 liters of copper sulphate(pentahydrate) per hour, NOTE:this is only how much copper sulphate is being used total in the solution which is 30% of the total liters used of solution because 25% of the water is inside the copper sulphate, the other 70% is just water. If you want the liters per hour of solution total, it is 34964.62 litres per hour of your 5% solution. I hope this was what you were looking for, I saw noone had answered and decided to try and get you what you needed.
What would you see if you dropped a piece of magnesium ribbon into some copper sulphate solution in a test tube?
If you drop a piece of magnesium ribbon into copper sulphate solution, you would observe a redox reaction where the magnesium displaces the copper in the solution. This results in the formation of copper metal and magnesium sulphate, with a color change from blue to colorless as the reaction progresses. Additionally, there may be bubbling and fizzing observed as the reaction occurs.
What would be seen in a reaction between copper sulphate and magnesium?
magnesium+copper sulphate =no reaction
What would happen if you added copper sulphate to water at room temperature?
Copper sulfate is soluble in water and dissociated in ions (Cu2)+ and (SO4)2-.
Can copper displace iron from iron sulphate solution?
In the normal conditions, it is not possible as iron is more reactive than copper. However, it is possible in an an electrolytic cell where an opposite electric potential is applied opposite to the normal potential so that the reaction could take in the opposite direction. In this case copper would be able to replace iron from iron sulphate.
What happens when you mix copper sulphate solution and zinc?
Adding zinc to copper sulfate will result in a displacement reaction that will create copper metal to precipitate as a solid. CuSO4(aq) + Zn(s) ---> ZnSO4 + Cu(s) This reaction is quite exothermic too, meaning it will give off alot of heat - enough to make it too hot to hold the reaction beaker in bare hands.
What effect would dissolving some copper sulphate crystals in the water have on its boiling point?
Adding copper sulphate crystals to water will raise the boiling point of the solution, as the dissolved particles disrupt the water molecules, making it harder for them to escape as vapor. This results in an increase in boiling point compared to pure water.
What would happen if you leave copper sulphate in a dish with a lid on for 2 days at 21 degrees Celcius?
It will turn brown ish
Does copper sulfate have a concentration?
A copper sulphate solution can have different concentrations depending on how much copper sulphate crystals have been added into the water. A typical 1 molar solution of copper sulphate would need 250g of CuSO4, mixed with 700ml of H2O, with 10ml of H2SO4 added with another 290ml of water.
