0
Yes it can. But leave this work to a qualified electrician. The consequences of doing this improperly range from failure of the cooktop to work, to damage to the cooktop, to an electrical fire, to injury or death due to electrocution. The hazards cannot be stated strongly enough.
Wiki User
∙ 14y ago
Wiki User
∙ 17y agoNo, you must break it down to a 120 volt supply.
Add your answer:
Earn +20 pts
What adapters do you need to plug your 240V Ac plug into a 110V AC supply?
There are no adptors to plug a 240v plug into a 120v receptacle. 240v requires two hot wores and a neutral and ground. 120v requires one hot wire, a neutral and a ground. If you have something that runs on 240/120 you need the cord and adaptor that came with the equipment as you willl need the wires to mate up accordingly.
Can you use a 120v cord that will fit a 240v socket the appliance is 240 and the cord is thick?
120v and 240v cords usually have different end configurations and will not plug into the different recepticles. However, if you changed the plug end, and the cord has the proper size rating, then yes, you could use the same cord. But, it also depends on the cord too. Most 120v cords only have three wires in them. One "hot one "neutral" and one "ground" wire. A 240v cord would have FOUR wires, two "hot" wires, one neutral wire, and one ground wire. Therefore, if you changed the voltage from 120v to 240 using a 3 wire cord, you'd not have a ground wire and that could be VERY dangerous. Note that occasionally a 240v device (e.g. some motors) will only need three wires (red,black,green, no neutral) and can be wired with a 120v cord if the cord is rated for 240v.
How do you hook up a 3 wire water herter to 4 wire circut?
4 wire household wiring is black, red, (hot wires) white (neutral) and bare or green (ground wire). You say 3 wires. Is it 120v or 240v. If its 240v which is more common just use the two hots and the ground and cap off the neutral wire.
WIll sump motor blow if I connect 240V?
It may not blow, but it will turn twice as fast and burn out very quickly. It is meant for 110 only. Check the sump pump. Some of them can be wired either 120v or 240v. If yours is like that, just wire the motor for 240v and plug it in.
On a 220 volt circuit where the white wire is common how many volts would the red wire be?
3 OR 4 . you only need 2 wires for 220, 1 phase is 120v between 2 of them its 220v . you also should have a ground for the third wire ,and the newer stuff requires a neutral or white wire for the 4th wire. hope i helped , D
I have 240V 3 wire twistlock plug and want to wire it so I have 120V outlet?
Don't!
What adapters do you need to plug your 240V Ac plug into a 110V AC supply?
There are no adptors to plug a 240v plug into a 120v receptacle. 240v requires two hot wores and a neutral and ground. 120v requires one hot wire, a neutral and a ground. If you have something that runs on 240/120 you need the cord and adaptor that came with the equipment as you willl need the wires to mate up accordingly.
Can you take single phase of 120V with a hot wire and a neutral step up to 480v and then step down to 2 phases of 120V or do you have to input 2 phases of 120v to get 240V out?
Theoretically that can be done with transformers, but the power available would still be limited by the circuit breaker on the original 120 v supply.
What is 2 wire plus ground 240V?
With one interpretation of this question, the answer would be two 120V wires and a ground.
Can you use a 120v cord that will fit a 240v socket the appliance is 240 and the cord is thick?
120v and 240v cords usually have different end configurations and will not plug into the different recepticles. However, if you changed the plug end, and the cord has the proper size rating, then yes, you could use the same cord. But, it also depends on the cord too. Most 120v cords only have three wires in them. One "hot one "neutral" and one "ground" wire. A 240v cord would have FOUR wires, two "hot" wires, one neutral wire, and one ground wire. Therefore, if you changed the voltage from 120v to 240 using a 3 wire cord, you'd not have a ground wire and that could be VERY dangerous. Note that occasionally a 240v device (e.g. some motors) will only need three wires (red,black,green, no neutral) and can be wired with a 120v cord if the cord is rated for 240v.
Can you connect a 15A 120V circuit to one phase of a 240V stove circuit without overloading the stove circuit?
Short answer: probably not. Longer answer: It depends on the size of wire feeding the stove, the stove amperage, and what you intend to connect to the new 15A circuit. If you just want to wire a light for the garage, sure go ahead. If you want to install a receptacle for a microwave oven, no way. Make sure you put a fuse to protect the circuit you are connecting.
How do you upgrade from 120V 15A to 120V 20A or from 240V 20A to 240V 30A?
You have to replace the wire (as you are increasing the current capacity), the outlet, and the breaker. Essentially you have to remove the old circuit and put in a new one. You can't reuse parts of the old circuit as you are increasing the current capacity and they would be underrated.
How do you wire 240V to 120V?
What specifically are you wiring? A light bulb would operate dim, a motor will burn up. The current increases thereby requiring larger wire and current protection.
How do you hook up a 3 wire water herter to 4 wire circut?
4 wire household wiring is black, red, (hot wires) white (neutral) and bare or green (ground wire). You say 3 wires. Is it 120v or 240v. If its 240v which is more common just use the two hots and the ground and cap off the neutral wire.
How do you wire 12V AC to 120V DC?
You would need a 12VDC to 120VAC power supply.
WIll sump motor blow if I connect 240V?
It may not blow, but it will turn twice as fast and burn out very quickly. It is meant for 110 only. Check the sump pump. Some of them can be wired either 120v or 240v. If yours is like that, just wire the motor for 240v and plug it in.
How can you get 240V single-phase power from a 240V 3-phase service Can you just connect to two poles of the 240V 3-phase service?
If the 240V 3-phase service is 240V phase-to-phase, then you can get 240V single-phase by simply picking two phases (poles, as used in the question) and connecting the load across them. This is simply one third of a standard delta connection. If you need 120V/240V split phase, i.e. with a neutral, as used in residential services, you will need a transformer. If the service is actually a four wire "quadraplex" service, however, you will probably already have that 120V/240V with neutral connection phase available. In this case, you will need to pick the two phases correctly in order to get the proper 120V service half.
