0
When operating refrigerant recovery or recycling equipment the following precaution should be followed?
Wiki User
∙ 8y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is the exact difference between and instrument and equipment?
An Instrument is a device or devices used to carry out a measurement (from the International Society for Pharmaceutical Engineers ISPE). An Equipment is a discrete non-consumable item either operating stand-alone or combining several instruments or pieces of equipment. An instrument is also a piece of equipment.
What is difference between equipment and machinery?
Equipment - are machines or major tools necessary to complete a given task. The tools a mechanic needs to repair a machine are an example while Machine is A system or device for doing work, as an automobile or a jackhammer, together with its power source and auxiliary equipment. Machines are devices that need a person's attention when operating. Equipment are devices that do not need this attention. Examples: a refrigerator is equipment, a steel cutter is machine, a stove is equipment, a computer or a fax are machines; we call it anyway, "fax machine". Your car is machine/you operate it; your house, though, is "equipped with A/C and fan" because you do not pay attention to them when operating. The water heater is equipment. The pressure washer is machine, the air-compressor is equipment.
Is air conditioner purchased for the computer room a leasehold improvement or furniture and equipment?
Depending on whether the air conditioner is a "central operating unit" or if it is a "stand alone unit". The stand alone is an equipment purchase whereas a "central" is now part of the building.
What does the SEER rating say about an air conditioner?
The SEER metric is used to measure a heating and cooling systems performance, which is determined largely by the HVAC equipment operating efficiency. SEER stands for Seasonal Energy Efficiency Rating.
Why dc components operate at low voltage compared to ac component?
Because equipment operating on DC is usually low-power electronic equipment, and it uses a power-supply to convert the house AC supply to DC at the right voltage. Most appliances needing high power are designed to run on AC because that is the normal supply to houses.
When viewing refrigerant through the liquid sight glass what is an indication that the system is low on refrigerant?
Bubbles visible in the glass with the system operating.Bubbles visible in the glass with the system operating.
How do you add refrigerant to 2004 Chrysler pacifica?
Refrigerant System ChargeWARNING: REFER TO THE APPLICABLE WARNINGS AND CAUTIONS FOR THIS SYSTEM BEFORE PERFORMING THE FOLLOWING OPERATION.After all refrigerant system leaks have been repaired and the refrigerant system has been evacuated, a refrigerant charge can be injected into the system. For the proper amount of the refrigerant charge, refer to the Underhood HVAC Specification Tag. An R-134a refrigerant recovery/recycling/charging station that meets SAE Standard J2210 must be used to charge the refrigerant system with R-134a refrigerant. See the operating instructions supplied by the equipment manufacturer for proper care and use of this equipment.REFRIGERANT CHARGE CAPACITYNOTE: Always refer to the underhood HVAC Specification Tag for the latest fill specification for the vehicle being serviced.CHARGING PROCEDUREEvacuate the refrigerant system .A manifold gauge set and a R-134a refrigerant recovery/recycling/charging station that meets SAE Standard J2210 should still be connected to the refrigerant system.Measure the proper amount of refrigerant (1.88 lb) and heat it to 52°C (125°F) with the charging station. See the operating instructions supplied by the equipment manufacturer for proper use of this equipment.Open both the suction and discharge valves, then open the charge valve to allow the heated refrigerant to flow into the system.When the transfer of refrigerant has stopped, close both the suction and discharge valves.If all of the refrigerant charge did not transfer from the dispensing device, open all of the windows in the vehicle and set the heater-air conditioner controls so that the compressor is engaged and the blower motor is operating at its lowest speed setting. Run the engine at a steady high idle (about 1400 rpm ). If the compressor will not engage, test the compressor clutch control circuit and repair as required.Open the suction valve to allow the remaining refrigerant to transfer to the refrigerant system.WARNING: TAKE CARE NOT TO OPEN THE DISCHARGE (HIGH PRESSURE) VALVE AT THIS TIME.Close the suction valve and test the system performance.Disconnect the charging station and manifold gauge set from the refrigerant system service ports.Reinstall the caps onto the refrigerant system service ports.Run the HVAC Control Cooldown test to verify proper operation.
What must A person operating farm equipment have?
Display a triangular red reflector mounted on the back of the equipment when operating on a public road.
What type of operating equipment does a rotary rig use?
The operating equipment of a rotary rig can be divided into three systems: hoisting, rotating, and circulation.
Which of the following equipment is required to be aboard while operating a motorboat in Louisiana?
Carry on board your certificate of numberCarry on board certification and number
Which of the following equipment is recommended while operating a motorboat in Virginia?
Personal Floatation Device for each person aboard
Where can I find a crane operator school in Missouri?
you can find the crane operating school in Missouri. can you visit the following website and search for the location in missouri website is www.heavy-equipment-training.com/
What are the disadvantages of operating network in special equipment?
penis
How can you save your equipment when the neutral wire becomes disconnected?
There is nothing to save. When the neutral wire becomes disconnected the equipment just stops operating. Disconnect the power supply, reconnect the neutral and the equipment will start operating again.
Why is it important to follow manufacturers instructions when operating equipment?
Office equipment is usually supplied with instructions. These provide guidance on the setup and functions of a piece of equipment.It's best practice to follow manufacturers' instructions in order to fully understand the equipment and get the most out of it.Not following manufacturers' instructions can result in damage being caused.Some of the most important reasons for following manufacturers' instructions are:Health and safetyEfficiencyMaintenanceManufacturers' guarantees.
Standard operating procedures when handling equipment?
day to day
What are the standard operating procedure to be when handling equipment?
just touch it then =)
