0
Remove the negative first and connect it last. The issue is that, if the tool you are using could accidentally touch ground, and you started with positive, then you would have a high current short and potentially an explosion. In car batteries, I always start and finish with ground.
What else can I help you with?
When removing the battery leads from the terminals of a car what lead do you remove first?
Remove the ground or negative cable first when disconnecting your car battery.
When removing the battery leads from terminals you remove what first?
Remove the negative cable first and when installing the new battery connect the negative last.
How do you change battery in suzuki burgman 400?
Open Glovebox, LHS Remove Battery cover by removing screw and lifting cover gently away. Disconnect battery leads, (Negative first) Battery slides out lifting gently.
When removing the battery leads from the terminals you do what first?
Disconnect the negative - terminal first, then the positive + terminal. Unfasten the battery hold down clamp. When reinstalling the terminal connections connect the positive terminal first.
When removing battery leads what lead should be removed first?
The battery lead that is not the earthed lead should be removed first. If the negative lead goes to ground then first remove positive and vice versa. This is true also for any non vehicular electrical device although the earthed lead is less easy to find but is almost always negative.
How do you change a battery on a 2007 Jeep Patriot?
The same way you change the battery in a ford f150, a dodge ram, a chevy suburban, a gmc sierra, or any other car on the market. You remove the cover, if applicable, disconnect the leads, (positive + first), remove the battery, put the new battery in, reconnect the leads (negative - first) and replace the cover, if applicable.
Can you charge a battery in a motorcycle without removing it?
The basic answer is yes. By removing the seat you will expose the battery on most sport bikes and cruisers, this will allow you to view the battery and place the leads from a trickle charger on the battery. Always use caution not to cross the battery leads as you may damage the battery and or some electronic component. For Motorcycle related how to articles visit http://www.ronincycleparts.com
How do you change the battery on a 1988 Yamaha Virago 1100?
Remove left side cover, and remove bolt that holds the seat in the front near the back of the gas tank. After removing the bolt, CAREFULL slide seat forward, I say CAREFULLY because when it releases, you could smack the back of the gas tank. Remove right side cover, batter should slide out to the right. Disconnect leads, and clean leads thoroughly. Reinstall battery is reverse of removal. Put a little dielectric grease on battery terminals to keep them from corroding.
How do you remove the battery on a 1992 Harley Davidson Dyna Low rider Daytona edition?
remove seat. remove two bolts holding bracket on left side of battery tray remove top bolt visible after seat is removed in step 1 disconnect battery leads remove battery
Change the battery on a 2002 vw passat?
Lift the hood. Between the windshied wipers is a hidden panel with battery markings on it. Remove the panel. Disconnect the battery leads, I prefer to remove the ground (black) first then the red second. Check to see if there is a battery retention bolt or strap holding down the battery and remove it if its there. Take out the battery and drop in the new one making sure to reconnect all cables and any battery tie-down stuff.
After jump starting your bike it stalls when removing leads?
If your bike stalls after removing the jump leads, it likely indicates that the battery is not holding a charge or is faulty. This could mean the battery is too weak to power the bike without assistance. Additionally, there might be an issue with the charging system, such as a faulty alternator or regulator. It's advisable to check the battery's condition and the electrical system to diagnose the problem accurately.
How do you change coil pack and leads on mondeo v6?
To change the coil pack and leads on a Mondeo V6, start by disconnecting the negative battery terminal for safety. Remove the engine cover if applicable, then locate the coil pack; disconnect the electrical connectors and unscrew the coil pack. After removing it, replace the old leads by pulling them off the spark plugs, and attach the new leads to the coil pack and spark plugs. Finally, reinstall the coil pack, reconnect all connectors, and reattach the battery terminal.
