answersLogoWhite

0

find amphere required

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

What is the setting in air circuit breaker?

"The setting" is not clear. There can be lots of stuff in a breaker control cabinet that could be deemed to have a "setting".


What is the requirement for energizing a 120 volt circuit breaker?

Before energizing a breaker for a circuit, the circuit has to be clear of any short circuits or grounds. This can be accomplished by the use of a megger on the correct voltage setting.


What should be the short circuit setting of the feeder breaker of a transformer so that it does not trip on short circuit fault in secondary side?

You need to model this - the line impedance and transformer impedance, and the voltage will determine this. There is no "one size fits all".


What should the instantaneous trip be set at for a 100 amp breaker?

The instantaneous trip setting for a 100 amp breaker should be set around 500-1000 amps to allow for momentary inrush currents without tripping the breaker. It's important to refer to the manufacturer's specifications for the specific breaker model to determine the appropriate setting.


Where can you find a self re-setting circuit breaker for a 65 Mustang?

The only place I remember a self reseting circuit breaker on my 67 is the line the feeds the power convertible top. But in general, most parts stores have circuit breakers like that, you simply need to know how large (how many amps) you want to buy.


What is the maximum capacity of a 60 amp breaker panel and how can it be safely utilized in a residential setting?

The maximum capacity of a 60 amp breaker panel is 60 amps. To safely utilize it in a residential setting, make sure not to exceed the total amperage of the panel with the combined load of all connected devices. Regularly inspect and maintain the panel to prevent overheating and electrical hazards.


How many recs can a 20 amp breaker handle?

The electrical code states you can load a breaker to 80% of its capacity. The electrical code also states that, for loading purposes, one receptacle can be treated as one amp. Therefore, by code, a 20 amp breaker can supply 16 receptacles. The NEC (National Electrical Code) used in the United States has no requirement on the number of receptacles on a 20 amp circuit in a residential setting. The circuit should only service 500 sq. ft. of the dwelling, so a room for example of say 20 feet by 25 feet would be 500 sq. ft. It would require one 20 amp circuit. This circuit could also be used for the lighting load in this room. This is the minimum requirement to meet code and not always the best wiring practice.


How do you check amp draw?

Amperage is measured by a multimeter. First determine the amperage rating on the multimeter. Next, select the appropriate setting on the tool. The next step is to set the range on the multimeter. Make sure to plug the leads into the appropriate terminals. Run the circuit through the multimeter to measure the current. Turn off the breaker, make sure the AC circuit is turned off, then rewire the circuit.


What is the purpose of I3 in mccb?

In a Molded Case Circuit Breaker (MCCB), I3 typically refers to the third current setting or rating, often associated with the overload protection function. It helps define the maximum current that the breaker can handle continuously without tripping. This setting is crucial for protecting the electrical circuit from overload conditions, ensuring safe operation, and preventing damage to equipment. Properly setting I3 helps balance the load and enhances the reliability of the electrical system.


Does breaker trip when circuit it is protectiong got wet?

Not unless the leakage current gets higher that what the trip setting of the breaker is. In many underground conduit systems the feeder conductors are in water continuously due to leaks in the under ground conduit system.


What will be the effect if the d.c motor is directly connected across the supply without starter?

At zero rpm a dc motor draws a current that could be enough to blow the circuit breaker. In that case it is normal to place a resistor in series to limit the current to slightly below the circuit-breaker setting. The resistor is switched out after the motor runs up.


Can circuit breakers help to prevent building fires?

Breakers limit the current on the conductor to a safe level, too many appliances plugged in. You trip a breaker, hopefully you then transfer load to another circuit. Breakers use two different methods to accomplish this, one uses a bimetallic strip and the current passes directly through, too high a current causes the strip to deflect. It acts on a mechanism much like the sear in a guns trigger, the deflection pulls the trigger causing a spring to open the contacts and turn off the circuit. Another type is thermal magnetic, current passing through the breaker causes a magnetic field to act on a coil tripping the breaker. When breakers are wired and work properly they prevent fires!Bending metal opens a switch