Needs a Topic
When visually checking the burner assembly for damage you should check?
Asked in Fossil Fuels
Can used car oil be used in home oil burner systems?
Asked in 2000-2005 Dodge & Plymouth Neons, 1995-1999 Dodge & Plymouth Neons, Timing Belts and Chains
How do you know there is valve damage on a 1999 Dodge Neon when timing belt breaks?
What do you do if you have no power going to your car radio?
Can Mercury toxicity cause hypertension and tachycardia?
Car door wont close?
Try checking the latching assembly on the door. If it snaps shut before the door colses, it keeps the door from closing. With the door open, look at the assembly while pulling the door handle to open. Use a screw driver and snap the latch that holds the door shut down. It should pop back and reset. Worn out door hinge pins and bushings lead to poor alignment and damage to latch and striker pin.
Asked in Bunsen Burners
What happens when the hole on a Bunsen burner is closed?
Will I damage My engine in any way if I dont put a quart of oil in the oil filterhorizontal assembly.?
Asked in Winchester Firearms
How do you reassemble a Model 52 heavy barrel rifle?
Asked in Ford F-150
How do you make your four wheel hub stop making noise and fix it you have replace the hub assembly and the vacuum switch on the firewall?
Asked in Hydraulics
Can you disassemble a hydraulic stylist chair once assembled?
Asked in Dodge Caravan, Dodge Grand Caravan
What does a tune up for a 1996 Dodge Caravan consist of?
A tune up consists of checking/refilling all fluids, checking the battery and cleaning corrosion if present, replacing the spark plugs and checking/replacing the wires, check and/or adjusting the drivebelt and replacing if necessary, checking and/or replacing the air filter, checking and/or replacing the PCV valve. (Check it by first removing it and shaking it; if it rattles really loud, it's fine..If it doesn't rattle, replace it.) Also check the hoses for damage, and sometimes it is necessary to replace the fuel filter during a tune-up.
Asked in Car Sounds
What makes your car make a grinding noise instead of starting?
How do I change the front corner parking light on a 03 dodge ram 1500 you cannot figure out how to get to the bulb or to get the light assembly off?
There are three 10 mm bolts that hold the headlight assembly in. Two are visible on the front side of the headlight assembly when the hood is up. The other is below the light assembly where the back of the light assembly meets the fender. It is accessed from the front and will require a socket extension. Once the bolts are removed, gently pull the headlight assembly forward. You will see two long plastic pins on either side of the assembly. Pull the light assembly forward until they are clear of the holes. You should now be able to swing the assembly out far enough to reach the directional bulb socket. Twist the back of the bulb assembly about 45 degrees and then pull the bulb assembly out of the socket. Replace the bad bulb, ensuring that you do not touch the bulb with your bare hands and leave oils behind, which will damage the bulb once it gets hot. Reassemble in reverse order.
Asked in Air Conditioning and Coolant, Clutches and Flywheels, Chrysler Sebring, Jeep Wrangler Sport
Need ac compressor for 2001 sebring coupe Doesn't appear to be aftermarket available Can just the clutch assembly be repaired?
Asked in Microbiology
What happens when a bacterial smear is overheated?
Asked in Lawn Mowers and Garden Tools
Why does my rider lawn mower turn off when i engage the deck?
Asked in Car Starting Problems, Nissan Altima
What is wrong with a 2000 Nissan Altima if you put your key in the ignition and it won't turn?
Wrong key or the tumbler assembly is worn out and must be replaced. Try spraying powdered graphite in the lock assembly as that may help. Do not use WD40 or any other liquid lubricant. If you have in the past, then spray inside the tumbler assembly with electronic cleaner and let set for 5 minutes to allow it to evaporate. Then spray with powdered graphite. If this does not work the assembly must be replaced. Also using a heavy key chain will cause this sort of damage.