A 6-30 plug/receptacle does not use a neutral. It has 2 hots and a gnd, all sized to #10 gauge wire and tied in to a two pole 30a breaker.
In a 6-30 3 prong female plug, there are two hot wires, which are usually black or red, and these connect to the two hot terminals. The neutral wire, typically white, connects to the neutral terminal, and the green wire, which is the ground wire, connects to the ground terminal.
I,m going to bypass the generator and plug into the house for my race car trailor. Once I pull the plug from the gewnerator I will have a four prong male need to plug into a for prong female then be able to plug into a house socket.
On a three prong plug there will be a neutral blade, a "hot" blade and a ground blade. The neutral blade is wider that the "hot" blade. In North America the ground blade is "U" shaped.
No, the wide prong is neutral it is the white wire. The narrow prong is hot it is the black wire. The round prong (in a 3 wire plug) is safety ground it is the green wire.
My question is WHY did you replace a four prong dryer plug with a three prong! 220 volt Electric dryers require two hot legs, a neutral and a system ground wire. Sounds as though you shunted one of the hots or the neutral. You need to install a four prong plug of the same configuration and wire it exactly as the original.
This is something that should not be done. If this was to be done you would be omitting the ground which in point can make it unsafe. I recommend changing the female end of the system and making it a 4 prong.
This is a 2 prong polarized female. However a 2 prong unpolarized male will easily plug into a 2 prong polarized female. just not the other way around.
I,m going to bypass the generator and plug into the house for my race car trailor. Once I pull the plug from the gewnerator I will have a four prong male need to plug into a for prong female then be able to plug into a house socket.
On a three prong plug there will be a neutral blade, a "hot" blade and a ground blade. The neutral blade is wider that the "hot" blade. In North America the ground blade is "U" shaped.
No, the wide prong is neutral it is the white wire. The narrow prong is hot it is the black wire. The round prong (in a 3 wire plug) is safety ground it is the green wire.
My question is WHY did you replace a four prong dryer plug with a three prong! 220 volt Electric dryers require two hot legs, a neutral and a system ground wire. Sounds as though you shunted one of the hots or the neutral. You need to install a four prong plug of the same configuration and wire it exactly as the original.
Sure i do
This is something that should not be done. If this was to be done you would be omitting the ground which in point can make it unsafe. I recommend changing the female end of the system and making it a 4 prong.
The green wire is for ground. You can attach that to any metal part of the frame. The red is the active and coincides with the lefthand prong into the plug and the black in this case should be the Neutral and ciocides with the right prong into the plug as seen standing behind the plug.
No you can not you will need to replace the plug with a 4 prong the same as the style of your oven and change your breaker to the correct Amp for your style of 4 prong plug
A NEMA 5-20 plug is a standard 3 prong plug. It wires the same as a NEMA 5-15 plug (Ground wire to the "D" contact, Hot to vertical terminal and neutral to the horizontal terminal (with the Ground terminal either at the top or bottom)).A 5-20P plug has the neutral blade rotated 90°. The 5-20R receptacle usually has a T-shaped neutral hole, to accept both 5-15P and 5-20P plugs.
There are shops that can make custom adapters for this. For example, evseadapters.com Or can also make your own adapter, if you know what type of outlet and plug you are working with, and which wires to connect to which terminals. Obviously one of the slots on the female connector will remain unused, most likely the neutral slot. The two hot connections and the ground connection would be used.
It is called a ground, and prevents you from electrocuting yourself if there is a tear in the cord.