Best Answer

More than likely their are none, go to the local tractor dealership and get yourself a grease gun needle and peirce the boots to grease it. i have a 2003. grease fittings i know of are on the ball joints of the upper control arm and the lower control arm, on either end of each tie rod, on top of pitman arm, on top of idler arm.

User Avatar

Wiki User

โˆ™ 2006-01-17 01:48:43
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Where are the grease fittings located on a 2002 Chevy Silverado 2500?
Write your answer...
Related questions

How many grease fittings on a 2005 Chevy Silverado 1500?

11 grease fittings

How many grease fittings on a 2012 Chevy silverado?


How many grease fittings 2008 Chevy Silverado?

2 Grease Fittings. One on each Tie Rod End.

Where are the grease fittings located on a 2002 Chevy silverado Z71 1500? has already answered this question

Where are the grease fittings on a 2009 Chevy Silverado?

I have only been able to find 2; Tie-rod ends. I have a 2WD W/T with a 4.3L.

How many grease fittings does a Chevy Avalanche have?


Where are the grease fittings on a 1999 Chevy Malibu?

There are no grease fittings on the new cars as the ball joints and steering assembly is maintenance free.

2000 Chevy Malibu does it have grease fittings or no?

Not on original equipment

Where are the grease fittings on 98 Chevy Blazer?

Grease fittings are located at upper and lower ball joints, outer tie rod ends, inner tie rod ends, pitman arm and both ends of idler arm.

Location of grease fittings on Chevy HHR?

It probably hasn't any.

2000 Chevy S-10 HOW DO YOU GREASE THE suspention?

If the components are original they are sealed with no grease fittings

How do you grease suspension on 2005 trailblazer?

You grease the suspension on a 2005 Chevy Trailblazer by attaching a grease gun to the grease fittings. Grease is then injected into the fitting until it leaks back out.

Where is my hood latch located on a 1999 Chevy Silverado?

where is my hood latch located on my 1999 Chevy silverado pickup

How do you stop sqeeks coming from fan on a 99 Chevy silveraldo?

grease your ball joints if you dont have grease fittings u will need to replace them

Where is the oil plug located for a 2007 Chevy Silverado ext cab?

"Where is the oil plug located for a 2008 Chevy silverado ext cab?"

Can you pack barrings on a 2007 Chevy Silverado classic?

NO. They are a factory sealed bearing, can not grease them.

Can you grease front wheel bearing on 2003 Chevy silverado 2wd?

No it`s sealed unit

Where is the antenna located on a 2002 Chevy Silverado?

In your a hole

How many grease fittings are there on a 1998 Chevy Suburban?

There is 11 grease fittings in the front end parts. You have 1 fitting in the front driveshaft, could have 1 in each u-joint. There may be fittings in the rear drive shaft too. There is 11 in the front Suspension for sure, and that is not counting the driveshafts.

Where is the pressure regulator located on a 2004 Chevy Silverado 4.8?

how to replace a fuel line presure regulator on a 2004 4.8 chevy silverado

Where is the ecm located on a 1981 Chevy Silverado?

no ECM's in a 1981

Where is the Speed Sensor located on a 1999 Chevy Silverado Z71 4WD?

On the 1999 Chevy Silverado Z71 4WD, the speed sensor is part of a module. It is located next to the transmission housing.

Where is the coolant sensor on a 95 Chevy silverado located?

The 1995 Chevy Silverado coolant sensor is located on the front of the engine. The coolant sensor will be a few inches above the thermostat housing.

Where are the grease fittings located on a 95 chevy 1500 rwd?

They are usually on the tie rods etc wherever there are bushings and easily visible from underneath. I am not sure if there are any on the rear of your model unless it has a sway bar, but you should be able to see them all and service them with a grease gun.

How do you grease 2002 Chevy silverado 4x4 wheel bearings?

You can't, They are a sealed bearing that's in the hub Assy.