0
Where can a circuit with two lamps with single pole switch fluorescent lamp with two 2 way and an intermediate control can be used?
Wiki User
∙ 11y ago
This type of circuit would never be used. The two way fluorescent system would depend on the voltage being supplied by the two lamp circuit switch. If the switch turns off the two lamp circuit the rest of the circuit with the fluorescent fixture would become inoperable.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
How can an intermediate switch be used with a 2-way switch system to control a light from four floors?
A two way switch is UK terminology for a North American three way switch. Though the switch has two names it is still a Single Pole Double Throw switch that has three terminals. North American terminology. The circuit is the same as the three way switch system. To control from four locations just add another intermediate switch. For the system to work properly the new intermediate switch has to be adjacent to the existing intermediate switch. The connections must run - three way, intermediate, intermediate, three way.
What type of switch would be used to control a lighting load from one control point?
In this type of situation, where there is more than one lighting circuit, a lighting contactor would be used. These types of contactors can be obtained in four and five pole configurations. Make sure that the contactor is rated for lighting loads and not motor loads. A normal switch, single pole single throw, would be used to switch the contactors on and off. A single switch could then be used to control as many contactors as you need to operate the lighting circuits.If there is just one lighting circuit, the total circuit amperage must be known, then the switch would be sized to the amperage of the circuit.
Can a single pole switch replace a starter in a fluorescent lamp?
No, a starter must be used.
A circuit that has 2 objects connected in a single path is a what?
a series circuit
Can you use 3 phase circuit as 3 separate single phase circuit?
yes we can use as a single phase circuit because at practise directly the 3-phase circuit is made by combining the three single phase circuits
Can a single pole switch replace a starter in fluorescent lamps?
No, a switch is used to control the circuit voltage that is applied to the fixture for turning the fixture on and off. The starter in the fluorescent fixture is used to start the current flowing through the filaments in the fixture's tubes. After a specific time, the starter heats up the circuit is opened and the current then flows through the fluorescent tubes.
How can an intermediate switch be used with a 2-way switch system to control a light from four floors?
A two way switch is UK terminology for a North American three way switch. Though the switch has two names it is still a Single Pole Double Throw switch that has three terminals. North American terminology. The circuit is the same as the three way switch system. To control from four locations just add another intermediate switch. For the system to work properly the new intermediate switch has to be adjacent to the existing intermediate switch. The connections must run - three way, intermediate, intermediate, three way.
Can a single pole switch replace a starter in a tube light?
No. Starter comes in the circuit initially and then cuts off once the tube is on. If you use the switch, it wont be cut off automatically. If you want to use the switch manually then it technically possible to do so
What is a 3 way switch?
A three way switch is a switch that is used in a lighting circuit that allows the light fixture to be turned on from three separate locations within the building. In electrical terminology this switch is also referred to as a SPST, Single Pole Single Throw switch. The switch has three individual terminals of which two are always connected. These switches are usually located at the far extremes of the circuit with an intermediate switch between them. This intermediate switch is referred to an a four way switch.
What is a 3-way switch?
A three way switch is a switch that is used in a lighting circuit that allows the light fixture to be turned on from three separate locations within the building. In electrical terminology this switch is also referred to as a SPST, Single Pole Single Throw switch. The switch has three individual terminals of which two are always connected. These switches are usually located at the far extremes of the circuit with an intermediate switch between them. This intermediate switch is referred to an a four way switch.
What is the circuit with a single path?
Series circuit
What is a circuit with a single path?
Series circuit
Why is an electrical circuit a series circuit?
It uses a single battery
Why is electrical circuit a series circuit?
It uses a single battery
What type of switch would be used to control a lighting load from one control point?
In this type of situation, where there is more than one lighting circuit, a lighting contactor would be used. These types of contactors can be obtained in four and five pole configurations. Make sure that the contactor is rated for lighting loads and not motor loads. A normal switch, single pole single throw, would be used to switch the contactors on and off. A single switch could then be used to control as many contactors as you need to operate the lighting circuits.If there is just one lighting circuit, the total circuit amperage must be known, then the switch would be sized to the amperage of the circuit.
A circuit in which all parts are connected in a single loop is called a?
A circuit in which all parts are connected in a single loop
Can a single pole switch replace a starter in a fluorescent lamp?
No, a starter must be used.
