Car Stereos and Speakers
Pontiac Grand Am
Grand Am SE

Where can you find an factory stereo wiring harness for an 1992 Pontiac Grand Am SE 4dr?

131415

Top Answer
User Avatar
Wiki User
Answered
2005-11-05 05:14:37
2005-11-05 05:14:37

MAYBE WAL-MART IF NOT A STEREO INSTALL SHOP

001
๐ŸŽƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Related Questions


Remove the retaining cover from your factory stereo. Remove the factory stereo retaining bolts. Slide the factory stereo out. Remove the wiring harness and the antenna cable from the back of the factory stereo.


Remove the 2002 Dodge Durango factory stereo decorative cover. Remove the factory stereo retaining screws. Pull the factory stereo out. Remove the wiring harness and the antenna cable from the back of the stereo.


All i had to do was by the in dash kit and wiring harness and it should plug right in


you need to pop out the frame and unscrew the radio. You will need a wiring harness for an after market stereo.


Remove the decorative stereo retaining cover. Remove the stereo retaining screws. Slide the stereo out and remove the wiring harness and the antenna cable.


You need to remove the wiring harness of the stereo and pull it out. It is fairly easy to replace this with something more advanced.


if your not going to use the old factory stereo, take it apart and you will find that the circit board is labled where it plugs in. Or go to your nearest stereo shop and get a wiring harness for $20.


The best thing to do is to buy a wiring harness for your car and new stereo. These are readily available on eBay from $15. Just search for 'stereo wiring harness'.


In my 1995 Metro there is no clock, other than the one that is in the stereo. If the stereo is bad, just replace it. You will need a new stereo, a wiring harness if you don't want to hack up the old factory harness, and a install kit to make the stereo fit in the hole if the old stereo is factory. Then just follow instructions included with these parts.


color codes for wiring on factory stereo on 2008 Nissan sentra?


if factory wal mart sells wire harness and it does some after market serios


http://www.modifiedlife.com/1993-pontiac-bonneville-car-stereo-wiring-schematic/


The factory wiring harness for the trailers will plug in under the back of the vehicle in the area of the spare tire, the harness plugs into the wiring harness for the tail lights.


YOU CAN GET A WIRING KIT THAT PLUGS STRAIGHT INTO THE FACTORY HARNESS AT A STEREO SHOP OR WAL-MART FOR ABOUT $15. COMES WITH DIRECTIONS AND PICTURES. HOPE IT HELPS


Connect the wiring harness to the back of your 1995 Buick LeSabre stereo. Secure the stereo with the stereo retaining screws.


The 1999 monster truck stereo wiring diagram can be obtained from most Mazda dealerships. The stereo has a wiring harness consisting of five wires.


If you are looking to install an aftermarket stereo in you Saturn it is easiest to buy the factory wiring harness adapter from your local audio components retailer and not hack off the factory plug. The harness adapter has all wires identified and is included for free if you buy your stereo from Crutchfield.com. good luck


Go to Wal Mart or Autozone and buy the harness adapter kit. Wire the connector to your stereo, and then plug the connector in the factory stereo harness and you are done. Easiest and cleanest way to install aftermarket stereos. Cost less than $20. or........ go to www.12volt.com.....right there hey have the wiring diagrams for almost n e thing


When making changes to a car it is important to have a diagram of the area. The wiring harness diagram to a Pontiac Grand Am can be found in its maintenance manual.


Find a company that sells wiring harnesses and they will be able to get a harness. Most of these include the wiring details. Look on eBay for 'Stereo Wiring Harness'


use this websitehttp://www.modifiedlife.com/1995-pontiac-grand-am-car-radio-stereo-audio-wiring-diagram/It helped me..


Attached the wiring harness and the antenna cable to the back of your stereo. Slide the stereo into the stereo slot. Tighten the stereo with the stereo retaining screws.


To remove a stock stereo, you will first need to remove the bezel from the stereo. Then, pull the stereo out of the dashboard and remove the wiring harness.


You can find a wiring diagram that shows you how to hook up a trailer wiring harness on a 1998 Pontiac Transport at most auto parts stores. A Pontiac repair manual should have the diagram in it.


Not too difficult. It will require about an hour and a basic understanding of car audio. This is not fully detailed, just the basics. You will need to purchase 2 things. 1. Vehicle Specific Mounting Kit (http://www.crutchfield.com/S-2G4tD0QgWhJ/m_750/Car-Stereo-Installation.html) 2. Vehicle Specific Wiring Harness (same website) The process goes like this: 1. Remove the factory stereo 2. Install the mounting kit which will include a little plastic compartment to fill in the extra space created by having a smaller-than-factory stereo. 3. Connect the wiring harness to the vehicle's existing harness. This should be compatible with your replacement stereo (make sure they are compatible) 4. Connect your new stereo to the harness (which goes between your new stereo and the vehicles current wiring harness) and slide the stereo into place. Done! Enjoy.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.