answersLogoWhite

0

  • Car Computers and Sensors
  • Pontiac

Where do I find the oil pressure sensor on my 1991 Pontiac 6000 LE?

User Avatar

Wiki User

βˆ™ 2007-07-15 17:42:43

Best Answer
Copy

On the front of the motor right next to the oil filter, on the right side, you will see the OPS (Oil Pressure Sending Unit). It has a tin base, with plastic tube extending out of it, with a 2 to 4 wire plug on the end.

2007-07-15 17:42:43
This answer is:
πŸ€“
🀯
πŸ€”
User Avatar

Add your answer:

Earn +5 pts
Q: Where do I find the oil pressure sensor on my 1991 Pontiac 6000 LE?
Write your answer...
Submit

Related Questions

What is the gap on the spark plugs for a 1991 Pontiac 6000 le?

.060"


Where is the knock sensor on a 1991 Pontiac 6000 LE 3.1?

on the engine block below the exhaust manifold. you can see it best by looking through the front passenger wheel well


Where is crankshaft position sensor located on 1991 Pontiac 6000 LE?

Rear of the engine block (firewall side), below the center spark plug, just above the oil pan.


Where is the oil sensor on a Pontiac 1989 6000 LE with a 2.8 V6?

It is next to the oil filter.


Why won't my 1985 Pontiac 6000 start?

have a pontiac 6000 2.5 motor and it wont stay running


Where is th low side ac port on a Pontiac 6000 3.1l?

The Pontiac 6000 low side air-conditioner import can be found on top of the air conditioning compressor. The low side air-conditioner port will be labeled as the low pressure port.


Where is the ignition module on a 1985 Pontiac 6000?

On the distributor.


1985 Pontiac 6000 fan will not turn on?

Could be a bad coolant temperature sensor, fan relay or thermostat. keep in mind the fan motor itself may be bad.


What is measurements for installing new outer tie-rods on Pontiac 6000 fwd?

The replacement of outer tie rod ends onto a Pontiac 6000 does not require "measurements." However, the vehicle will need to an alignment after install. An alignment usually takes initial measurements of the wheel geometries, and the technician uses these to adjust the wheels back into specification. For the 1991 Pontiac 6000, the final year of production, the AC Delco Professional outer tie rod is part number 45A0230.


Where is the oil filter on a 1990 Pontiac 6000?

The oil filter on a 1990 Pontiac 6000 is located on the driver's side of the engine compartment. It is on the side of the motor all the way to the rear, near the firewall.


Where is the fuel pump located on a 1985 Pontiac 6000?

Fuel tank


Will the springs and struts from a 1989 Pontiac 6000 le wagon fit onto a 1989 Pontiac 6000 le sedan?

You could call your local auto parts store and they should know the answer to that one


Where can one find reviews for the Pontiac 6000 car?

There appears to be a large amount of information available for the Pontiac 6000 car. If one is wanting to view reviews these can be found on the Edmunds site as well as on Car Guru.


Where can you find a wiring diagram for a 1985 Pontiac 6000?

Wiring diagram of what component?


Diagram of Pontiac 6000 motor?

2.5L 4cyl base. Iron Duke


1990 Pontiac 6000 3.1 won't start. Repalced ignition module and tried a new pcm...no help. Good fuel pressure at the fuel rail 42 psi.?

First, double check your plug wire routing from when you changed the ICM. It could also be a bad crankshaft position sensor.


Where is the pepcock located on a 1990 Pontiac 6000 v6?

Should be at the bottom or rear of radiator


What is the pressure 6000 meters under the sea?

HUGE


What is barometric pressure at 6000 ft altitude?

850


Weight of 87 Pontiac 6000 se?

The weight of the Pontiac 6000 SE is recorded as being 3,021 pounds. This weight can be altered by aftermarket products which are installed on the vehicle or parts which may have been taken off of the vehicle since being manufactured.


Why does my Pontiac 6000 have a high idle?

A sticking choke or vacuum leak are two common causes.


When the 1988 Pontiac 6000 accelerated there is a loud screeching noise from front tiresWhat is it?

its called a burnout


How many ml in 6000 cm?

Of water? 6000 ml at standard pressure. For other compounds and elements, it depends on density.


What is the firing order for a 1986 Pontiac SE 6000 2.8 liter?

To The Owne of the 1986 6000 SE: The firing order is 1,2,3,4,5,6. Most Sincerely, Kristopher Gerbracht www.kristopher.gerbracht@juno.com


What does the model of Pontiac 600 LE look like?

http://www.carsurvey.org/images/pontiac_6000_1.jpg If you mean Pontiac 6000, not 600, which is an old Dodge model, then this is a picture of one.