0
Where do you find the plate and screws that holds the gun together?
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Where can you find the retainer that holds in the headlight bulb in for a 2000 Mercury Villager Sport It is black plastic and screws onto the socket that holds the head light?
Ford dealers have these.
What is a screws?
A screw is a simple machine used to hold things together. You can find screws in almost any piece of furniture such as chairs and tables.
Where can you find a wiring schematic for a 2001 Chevy cavalier?
you take the fuse plate off the side of the dash. there will be a plate on the other side you take it off to, remove the screws then you have more screws in the top of the glove box that u take out.after u take them out look on top of ur dash remove the vent plate take them screws out as well. then u should be able to pull the top of ur dash out. After doing that look where uu steeringwheel is u will have 3 screws to take out after u take them out u can can pull that off and pull or put u radio in and put it back together the way u took it off.
Where do you find the fuel pump on a 96 Mazda protege DX?
take the back seat out and there should be a thin metal plate with four screws in the middle of the car take that off then you will see the top of the gas tank take the 8 screws out of there and the pump is under that plate
Where is the combination flasher unit located on a 1995 Plymouth voyager?
Remove the dash panel that contains the emergency brake release handle. Behind this panel you will find a metal plate held in place with 4 screws. Remove this plate. The combination "turn signal & flasher" module is yellow and is located to the extreme left side of the assembly that holds the "plug-in" type devices.
Dash remove 99 altima?
to remove the dash trim around the stero unit, find the screws under the ac/heater controls that are on the trim, to remove the rest of the trim you need to remove the plate around the shifter too, so take the screws out of the shifter's plate. remove the rest of the screws around the trims and you should be able to pull the trim out of place.
How do you find screwa on Maplestory?
You don't find them, you make them or do a quest. To make them you'll need: One Bronze plate (Made from 10 bronze ores) One Steel Plate (Made from 10 Steel ores) Then go to any item maker (There's one in Henesys, Ellinia, Perion and Kerning City) and they'll make 15 screws for you. Or do this quest, John and Pink Flower Basket, and you'll get screws from him at the end of the quest. You don't find them, you make them or do a quest. To make them you'll need: One Bronze plate (Made from 10 bronze ores) One Steel Plate (Made from 10 Steel ores) Then go to any item maker (There's one in Henesys, Ellinia, Perion and Kerning City) and they'll make 15 screws for you. Or do this quest, John and Pink Flower Basket, and you'll get screws from him at the end of the quest.
Where do you find the plug that screws into the side of the barrel and holds the nipple on a Traditions Pioneer Rifle muzzle loader?
Dixie gun works website may have a drum for that one, dixiegunworks.com
How do you replace the exterior mirror on a 1996 Beretta?
To replace the exterior mirror on a 1996 Beretta, find a small plate on the inside of your door. Remove the screws and install the new mirror.
Where can you find the keyless entry code for a 2000 ford explorer Eddie Bauer?
It should be in the compartment that holds your jack, bold numbers stamped on a metal plate.
How do you get the ignition out of the housing in a 1984 Camaro?
Remove the steering wheel, the snap ring and plate, the signal light switch, and you will find the bolt that holds the lock cylinder
How do you change a license plate light on a 1979 Chevy Camaro?
how to change the license plate bulb onLook at the rear plate , then get on the ground so you can look up to the underside of the bumper, where the plate is. There are two Phillips screws the hold your plate light, remove both, pull down gently on the light, then turn it co you can see the rear and with both Hans turn the socket and pull, there you will find the bulb. change it and do the reverse to install.
