Want this question answered?
Simply press the alarm button on the dashboard while swithcing the key on and of for 5 times
SkyScan Model 31981B TO START THE CLOCK:1. Insert 2 AAA batteries with proper polarity (+) and (-)as indicated In the battery compartment.2. The LCD goes to default time and calendar 12:00:00AM (time) and 1-1 (Jan 1 2003).The alarm time is 6:00 AM.Default time zone is PST, default temp. readout Is degree F.3 The clock takes the temperature reading immediately then starts to search for the WWVB signal. Remarks: If you immediately manually set the time / alarm time / calendar the clock will slop its initial reception of the WWVB signet. It will resume to the WWVB reception automatically when the clock exits SET mode and no other button is pressed for 5 seconds.TO SELECT THE TIME ZONE:1. Press TIME ZONE button once, the LCD shows the time zone (the default time zone is PST).2- Press + or - - to set the time zone (PST>MST>CST>EST)3. Press the TIME ZONE or SET button to go back to the time display or it will automatically go back to the time display in 5 seconds.TO SET TIME, CALENDAR, 12/24HR AND C/F:1. Press the SET button once to set the Year: digits show '2003" and blink. Press + or - - to set the year.2. Press the SET button again to set the Date : small digits show " 1 - 1" (i.e. Jan 1st) and blink. Press + or - - to set the date. Press and hold + or - will increase the increment or decrement at a faster rate.3. Press the SET button again to set the Time : large digits in HR : MIN will show and blink.Press + or - to set the clock to the current time. Press and hold + or - will increase increment or decrement at a faster rate.4. Press the SET button again to set 12 / 24 HR readout. Upper LCD shows "l2Hr" and blink.Press + or - to choose 12HR or 24 HR time display format.5. Press the SET button again to select C/Freadout: the temperature readout (i.e. 68F) will blink. Press + or - to choose readout (i.e. 68F or 20C ). The default readout is In degree F.6. Press the SET button again to exit the setting mode and return to the normal display. Or it will automatically return in 5 seconds. **Special attention for usage in Arizona and Indiana.**Part of Arizona and Indiana do not have Daylight Saving Time (DST).Please slide the DST switch inside the battery compartment to OFF if the clock is used in these states.TO SET ALARM TIME ;1. To read your alarm time: press + or - once, the lower Month and Date digits will change to alarm time digits.2. To set the alarm time: press + or - again, the alarm digits will blink, Press + or - - to set your alarm time. Press and hold + or - will increase the increment or decrement at a faster rate..3. Alter you set the alarm, the clock will go back to the normal display automatically in 5 seconds.TO TURN ON/OFF THE ALARM:1. To use snooze alarmPress the SNOOZE / AL ON/0FF button until SNZ and (((o))) show on lower LCD.When the alarm beeps, press SNOOZE / LIGHT bar. The alarm will Sound again when the snooze periodis over. (See "To Program the Snooze Alarm " below)When the alarm beeps, press any key at the front to stop the alarm. The snooze alarm will turn on the following day at the same time.2. To turn on alarmPress the SNOOZE /AL ON/OFF button until (((o))) shows on lower LCD.When the alarm beeps, press SNOOZE / LIGHT. The alarm will turn on the following day at the same time.3. To disable the alarm permanently:Press the SNOOZE / AL ON / 0FFbutton until the SNZ and (((o))) clear from the lower LCD.TO PROGRAM THE SNOOZE ALARM:1. Press and hold the SNOOZE I LIGHT bar for 3-4 seconds. The small display will blink and show 05 (minutes) the default snooze duration. Press + or - to set the snooze duration from 5 minutes to 60 minutes.Note: The minimum snooze duration is 5 minutes.2. Press the SNOOZE I LIGHT bar once to go back to the normal display or the clock will auto exit if no further buttons are pressed after 5 seconds.
To set the clock time:Hold down the "time set" button.Turn the dial labeled "set" to change the hour.Press the alarm button again to move to minutes.Turn the "set" dial again to advance the minutes.Once you have set the correct time, press the "time set" button again to confirm the new time.To reset the alarm:Hold down the alarm (1 or 2) button (whichever alarm you want to reset).Turn the dial labeled "set" to change the hour.Press the alarm button again to move to minutes.Turn the "set" dial again to advance the minutes.Once you have selected your desired alarm time, press the alarm (1 or 2) button again to confirm the new alarm time.
Alarm which is sensitive to touch.
The link below is no longer active. Simply press mode to enter alarm mode. Then QUICKLY tap the set button to change time zones. Each time you press the set button it moves over one time zone to the right. If you hold the set button for two seconds it will begin setting the alarm, so just tap the button. See: http://home.comcast.net/~mark.flint/instructions-spc364.html page which contains the full instructions for the Sharp Atomic Clock (model SPC364). Here is the new link :) THANK GOODNESS FOR THIS! http://home.comcast.net/~mark.flint/spc364/
Simply press the alarm button on the dashboard while swithcing the key on and of for 5 times
you press the red button by the dashboard that says: "Deactive Alarm" Thank you.
It allows you to sit in the car with doors locked and stops the alarm going off while still in the vehicle
It's a triangular button on the middle of the dashboard, and it will turn off the flashers if the alarm is accidentally set off (the key fob alarm button will only turn off the horn beeping, not the flashers, if you accidentally push the key fob alarm button.)
push the small button about 3 sec.
there are alarm systems that have disabling features. there is either a reset button usually placed somewhere under the dashboard or resetting can be done with the electronic buttons on the key.
I'm not sure what you mean by "kill switch" But there should be a red push button on the bottom left of your dashboard. The switch can be used to reset your alarm system
Easy. Fuse 14 out take out the yellow wire behind the fuse only for alarm click the blue button to OFF under dashboard now fuse 14 in again
after you reconnect the battery you need to reset the alarm system. there should be a reset button (valet button) located under the drivers side of the dashboard. hold the button for 3 seconds then try to start the vehicle.
There is a toggle switch or button down under the dash on the left side of the dashboard....it's called a valet switch, not even my dealer knew this!!
Behind the dashboard on the floor
Pressing a fire alarm button.