0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is the function of back pressure valve in Boiler feed pump?
The function of back pressure valve is to prevent back flow to the pump in case there is an obstruction on downstream side of valve.
What is the difference between an air bleed valve and a pressure relief valve on a boiler?
They serve two different purposes. An air bleed valve is used to remove air from the circulation system. A pressure relief valve is designed to automatically open when certain pressure levels are reached.
How do you test a safety valve of a Boiler?
Raise the pressure in the boiler until the valve relieves and note the pressure at which it does so.
Boiler works but no hot water?
Sounds like you have a bad zone valve or zone pump. There is either a pump, and the zones in the house have zone valves, or each zone has it own pump. Zone valves go bad all the time, you can just replace the motor on it instead of sweating the new valve in. The box that is on top of the valve.
What is the application of boiler stop valve?
Stop Boiler Valve (or Crown Valve) is installed on an outlet line of a boiler. It's purpose is isolation of a boiler from a downstream steam line. Its position may be either open or close, it cannot be used for throttling of steam.
How do you bleed air out of baseboards that have no bleed valve?
By using the bleeder valve by the boiler
In boiler feed water line whether a non return valve should precede or succeed the delivery valve of feed water pump?
In boiler feed water line the NRV is normally installed between Pump and stop valve if the line is short and an another NRV is installed at boiler entrance and after stop valve if the line is long or pump is 10 to 15 m away from the boiler.
What is the function of back pressure valve in Boiler feed pump?
The function of back pressure valve is to prevent back flow to the pump in case there is an obstruction on downstream side of valve.
How do you bleed diesel pump on vauxhall frontera?
open bleed valve on top of distribution pump, crank engine till fuel squirts from valve, tighten valve, turn over couple times. Add heat and fire up.
How do you get the air out of a pump?
Bleed the air out while running your pump. Either through a specific bleed valve or by loosing the discharge pipe at the pump until only fluid runs out of it.
What is the difference between an air bleed valve and a pressure relief valve on a boiler?
They serve two different purposes. An air bleed valve is used to remove air from the circulation system. A pressure relief valve is designed to automatically open when certain pressure levels are reached.
Where is the check valve for fuel bleed off on a 1997 jimmy gmc?
Built into the fuel pump
Why two safety valve provide to boiler?
standby valve,
Do you have to bleed the fuel when replacing the injector lines on a 12 valve Cummins with a P7100 pump?
yesyes
How to drain a radiator in the house?
Not for the faint of heart! For a Combi/Evaporation boiler: Switch off the boiler. Take a reading of the boiler water pressure gauge. Shut off the radiator's thermostat valve(if fitted)/supply valve and return valves, connect a hose to the drain and put the other end into a large container below the level of the bottom of the radiator. Open the draincock first and then the air bleed valve and let the radiator drain. Close the draincock. When refilling the radiator put the anti-corrosion treatment in first then open the thermostat valve and return valve as wide as possible. when the air is expelled, close the air bleed screw. Using the fill loop restore boiler pressure. Put all thermostat valves(if fitted) to max and fire up the boiler. After the boiler has run for 10 minutes, switch off, or so go to the highest radiator and bleed out the air. WARNING: the water/steam will be very hot and likely to spit. Use a cloth as a barrier and to mop up any spills. Recheck the boiler pressure and top up as necessary.
What is the use of boilerfeed pump?
The boiler feed pump pumps hot feedwater into the boiler. The boiler pressure is to high for water to flow into it by gravity, so a pump is required.
How do you test a safety valve of a Boiler?
Raise the pressure in the boiler until the valve relieves and note the pressure at which it does so.
