Its located up and alittle to the right of coil packs on back
side of block
The knock sensor for the 1993 Chevy Cavalier is located in the back of the motor. It can also be located in the engine valve.
It is located either on the manifold or somewhere on the exaust
You have another problem other then the knock sensor if the engine will not start and run. A knock sensor will not cause the engine not to run.
The crankshaft sensor is located on the side of the motor towards the firewall. It is located more towards the oil filter,
i need to find location of fuel filter on 1993 Chevy cavalier
1993 Chevy cavalier 2.2l Spark gap is....................... 1.4mm
1993 Honda Civic EX's dont have knock sensors.
The neutral safety switch, on your 1993 Chevy Cavalier, is located beneath the shifting column. The switch can be accessed by removing the shifting boot.
Sorry I meant knock sensor on 1993 Chevy blazer k1500
It doesn't have a knock sensor on the 4.0 L OHV in a 1993 Ranger ( my 1995 Ford Explorer 4.0 L OHV engine doesn't have a knock sensor either )
it is located behind the coil packs
My book says 100 lbft.
where are the senders on a 1993 Chevy corica for the oil and temputer gages to reinstall
The cam sensor is the distributor.
It is the knock sensor. It retards the timing if the engine pings or rattels.
It is over by the starter, and screewed into the side of the engine block
The fuel pump is located in the gas tank.
purchase Haynes manual.
Depends on the condition of the car, check Kelly bluebook
trying to locate crank shaft sencor for 1993 Chevy lumna trying to locate crank shaft sencor for 1993 Chevy lumna
It doesn't have a MAF (Mass Air Flow) sensor.
The 1993 Chevy S 10 Blazer IAT sensor can be found on the top of the transmission. The IAT sensor will be near the front of the transmission.
in the catylitic converter (underneath car...connected to your exhaust
the elictronic control sinsor at on a 93 mercury villager
on top of the engine under the air box
it is the one in the fuse block marked inst or panel
GM vehicles are not equipped with an inertia switch.
PRETTY SURE OIL SENSOR
That year did not have a crank sensor on it.
does not have one just a map sensor
The sensors are located on the transfercase for your cluster panel
NO it don't. Was not used on that year.
You can find a 1993 Chevrolet Cavalier schematic diagram, for the wiring and cooling system, at most Chevrolet dealerships. You can also find the diagram at most auto-parts stores.
The VSS sensor is the vehicle speed sensor and it is located in the transmission. The purpose of it is to operate the speedometer and abs system.
The fuel level sensor would be located in the fuel tank.
The throttle position sensor is on the throttle body opposite of where the cables attach.
I don't know, check back in 1 year and we will tell you.........
If the engine is 3.8L SFI OHV the Knock sensor is located under hood, passenger side, front engine area, below exhaust manifold, mounted in engine block
The refrigerant capacity of a 1991 Chevrolet Cavalier is 36 ounces of R-12 Freon. This is the same for all Cavaliers produced from 1986 to 1993.
The crankshaft position sensor is located on the rear of the engine. It is mounted just above the oil pan on the engine block.
Under the intake manifold, right in the middle of the valley, on the block. The intake manifold has to be removed.
under the coil packs and the coil packs are connected to the spark plug wires
either right front corner behind headlight or on firewall by blower moter
off the driver side exhuast manifold
There is no cable....It's all done with a sensor and electronics.
The Jeep Grand Cherokee didn't exist until 1993.
It's in the rear of the engine not the front. It's hard to see but it's tucked up there.
That would be the engine coolant temp sensor for the dash gauge only. The sensor near the thermostat housing is the engine temp sensor for the ECM.
There is no cam sensor on a 93 3.1. Just a crankshaft sensor....which is located behind the harmonic balancer. WRONG! it does in Fact have a cam position sensor! its underneath the intake plenum!
like a sensor it screws into the back of the block has a 1 wire connector located in the intake manifold .expensive over $130 for a good product