Oxygen Sensors
Chevy Silverado
Mitsubishi Outlander

Where is the Oxygen Sensor on a 90 Caprice V6 43L?

678

Top Answer
User Avatar
Wiki User
2008-11-16 14:33:38
2008-11-16 14:33:38

There is one before and one after the catalytic converter.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

1977-85 Impala, 1977-90 Caprice

User Avatar

Any 1977-85 Impala or 1977-90 Caprice will work

User Avatar

I have a 90' Caprice with a 305 that I brought up to 130mph.

User Avatar

the oxygen sensor is grounded when you thread it into the exhaust manifold the oxygen sensor should have only 1 wire it should be purple the didnt start putting 2 or 4 wire sensors in until the early 90's there should be a ground from the battery to the block

User Avatar

well my 86 caprice is a 305 also and its a 5 quart capacity. so I'm goin out on a limb an guessing the 90 caprice is also a 5 quart capacity also. well my 86 caprice is a 305 also and its a 5 quart capacity. so I'm goin out on a limb an guessing the 90 caprice is also a 5 quart capacity also.

User Avatar

the crank position sensor can cause similar symptoms jeep is known for crank sensor problems

User Avatar

it producers 90% of our oxygen

User Avatar

in the fuel tank, its like $90 at carquest

User Avatar

There is no cam sensor on a 90 3.1. Only a crank sensor.

User Avatar

Unsafe oxygen level is below 90% oxygen saturation.

User Avatar

77-85 Impala, 77-90 Caprice, 78-83 Malibu, 78-88 Monte Carlo/El Camino

User Avatar

IF that is the Intake Air Temp sensor - It is probably on the throttle body. the other sensor is the TPS throttle position sensor

User Avatar

The sensor itself is going to range from $90-110 bucks at a part store (more at a shop of course), and then it is a pretty quick dig, I hear ... my shop was going to add $40 bucks to do that.

User Avatar

Where is the choke sensor on a 1991 Oldsmobile ciera 3.3L

User Avatar

Actually yes it will. Caprice/Impalas from 1977-1996 Share the same basic chassis. It will fit, also how do I know for a fact? I have a 9c1 rear end in my 88 caprice. Also just about any and all Suspension parts from a 91-96 caprice/impala will work with a 77-90 caprice/impala. However you will now have two different bolt patterns, unless you have a 80's 9c1 police package caprice which I believe did come with the same 5x5 bolt pattern as the 91's caprice/impalas

User Avatar

Any windshield from a 1977-85 Impala or 1977-90 Caprice. A contemporary GM B-body (Buick LeSabre, Olds Delta 88, etc) should work also.

User Avatar

90-100%.Anything below 90% saturation is considered hypoxic.

User Avatar

78-87 Monte Carlo is a G-Body GM car that is smaller than a 77-90 Caprice which is a B-Body GM car. The seats in a Monte Carlo will fit in a Caprice, but they may not look quite right. You will need to do bolt location modifications. I would not recommend trying to use a bench seat from a Monte in a Caprice. It is not wide enough.

User Avatar

A healthy individual would have a normal oxygen saturation of 97%-99%

User Avatar

A normal blood oxygen level should be 90 or above (90-99). Any level below 89 qualifies you for oxygen. 74 is low and it means your brain and body are not getting enough oxygen. You should be evaluated by a pulmonologist and you should be on oxygen.

User Avatar

there are two 02 sensors on a 97 they are easy to replace,i have seen these sensors for around 90$ which is high for an 02 sensor but can easily be done yourself, if you can find a low mileage one in a junk yard you could do it for a few dollars

User Avatar

I am in the process of replacing the speed sensor in my 90 prelude. It is located on the transmission. with a small cable with a plug on the end of it. Looking at it from the passenger side . you can see a picture of it on eBay.. just type in 1990 Honda speed sensor.. there are several...

User Avatar

there are two oxygen sensors. The sensors runs between 90-110 for OEM fit, the wire harness can pre-fab/wired. It is a safer bet for repairs. Deducting $200/tax for oxygen sensors (up and down stream) or with the mark up, it leaves $100.00 for labor/or $120 without markup The down stream sensor seems to easier to replace than the up stream sensor if you have a lift. The total time to do it on your own is about 1 and 1/2 hours, or 2 1/2 hours (slowly).


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.