Turn on radio - the word SAFE will appear in the display. Press th P.SCAN and RBDS buttons simultaneously and hold them down until "1000" lights up in the display.Release buttons.Do not, under no circumtances, continue holding them down or press them once again. This will cause the radio to consider the number 1000 to be the input code.Use station buttons 1,2,3,and 4 to enter the code number on your Radio Card. Use the button 1 to enter the first number 2 for the second number 3 for the third number and 4 for the last number.Once you have entered the code and it shows on the display,press the P.SCAN and RBDS buttons down again simultaneously and hold them down until the word SAFE appears in the display.Release buttons. Soon afterwards a frequency will be displayed.
Radio buttons need to be placed in the appropriate type of frame. A radio button's value is always static, however the frame that you bind the radio button to will have the value of the selected radio button.
The factory radio does not have a reset button.
# Turn on radio. The radio display shows "SAFE". # Press the P.Scan and RBDS buttons simultaneously and hold until "1000" shows on the display. Release the buttons. Do NOT press these buttons again, otherwise the radio will consider "1000" to be the code. # Use Preset buttons 1 ... 4 to enter the four-digit code number from your radio card. Preset button 1 corresponds to the first digit, Preset button 2 corresponds to the second digit, etc. Each press of the button increments the number by 1. # Once the code shown on the display is correct, press the P.Scan and RBDS buttons simultaneously and hold until the word "SAFE" appears in the display, then release the buttons. # The radio should unlock and be usable shortly afterwards. # If an incorrect code is entered, the word "SAFE" appears, first flashing and then continuously. You can repeat the above steps to unlock the radio once more, the number of attempts will be shown in the display. If an incorrect code is entered again, you radio will be locked for about one hour. After one hour - the radio must stay on and the key must remain in the ignition lock - if the display goes out, the you can repeat the above procedure to unlock again. The cycle - two attempts, one hour lock-up - still applies. # If you lose your radio code, contact your Audi dealer. nismogirlb14se.com
there is a little orange button on the radio that is the power button
Ever thought it might not be the right button?
Turn on radio - the word SAFE will appear in the display. Press th P.SCAN and RBDS buttons simultaneously and hold them down until "1000" lights up in the display.Release buttons.Do not, under no circumtances, continue holding them down or press them once again. This will cause the radio to consider the number 1000 to be the input code.Use station buttons 1,2,3,and 4 to enter the code number on your Radio Card. Use the button 1 to enter the first number 2 for the second number 3 for the third number and 4 for the last number.Once you have entered the code and it shows on the display,press the P.SCAN and RBDS buttons down again simultaneously and hold them down until the word SAFE appears in the display.Release buttons. Soon afterwards a frequency will be displayed.
Hit the AM radio button. You did not say it was a factory radio though.
If your 1998 VW Beetle has a radio preset button that will not push anymore, you can sometimes fix it by prying the button out of the radio with a butter knife. Then, clean behind the button and clean the button itself. Pop the button back into the radio.
If you mean reset button there is none. If you mean radio presets then they are right there on the radio face plate. They are numbered and easy to see.
Put batteries into a radio then press the on button
Turn the radio on. Press SET button. This puts the radio in (Program) mode. Press SEL button. This puts the radio in (Set Hours) mode. Press TUNE button up or down to adjust hours. Press SEL button. This puts the radio in (Set Minutes) mode. Press TUNE button up or down to adjust minutes. Press SEL button again to return to normal mode. Pressing the SEL button after this changes the display to (Radio Frequency) display or (Time) display.