There is an upper footwell panel on the front passenger side of the car. Remove the trim panel. This exposes the blower motor assembly. Find the electrical plug on the unit and unplug it. This will expose the resister screw and by removing the screw, you will be able to remove the resister for the blower. If the resister does not show continuity when tested with an ohm meter the resister needs to be replaced. If the resister shows continuity the problem may be the blower motor relay. Hope this helps on your 1998 Mystique.
The blower resistor is located behind the dashboard. It is found behind the heater near the center of the vehicle.
Its located in the a/c heater blower housing on the passengers side of the vehicle........
Not knowing what the vehicle is, they are generally found close to the blower motor.
The a/c heater blower motor resister is located in the vehicle on the passengers side inside the housing next to the blower motor...............Remove the blower motor resistor wire harness connector.Remove the blower motor resistor screws.Remove the blower motor resistor.
The blower motor fan cools the resistor so the resistor is usually located close to the blower.
The Resistor is located on the outside of the blower motor. Have to remove the blower from under the glovebox to get to it. The Resistor is located on the outside of the blower motor. Have to remove the blower from under the glovebox to get to it.
The blower resistor is located under the dash, near the floor, on the passenger side of the vehicle. I had to replace the resistor about a year ago. It is not an easy place to work in. You have to remove the blower unit in order to get at the resistor. Not fun, but rewarding when you actually do it yourself.
The blower motor resistor on a 1995 Ford Mustang is located near the blower motor. It is a plug with various colored wires on the passenger side of the vehicle behind the reservoir for the washer fluid.
where is the blower motor resistor located on 2002 gmc envoy?
That depends on the car, they are not all in the same place on every vehicle.
the resistor is located in the blower module which is located under the hood by the a/c evaprator case
Resistor is located behind the blower motor assembly.
The blower motor resistor is located on the lower right side of the HVAC unit housing inside the the vehicle under the dash on the passengers side........
The heater blower in a 2001 Hyundai XG300 is located on the passenger side of the engine. The blower resistor will be located on the firewall.
The blower motor resistor on a 1993 Nissan Altima is behind the glove compartment on the passenger side of the vehicle. To access the blower motor resistor, the glove compartment can be removed by lowering the bottom as much as possible and removing it from the hinges.
The blower motor resistor is generally located close to the blower motor.
The blower motor resistor is located under the glove compartment in a black shroud.
The 2001 Nissan Quest blower motor resistor is located on the firewall in the engine compartment. The blower motor resistor will be on the passenger side of the firewall.
i had a 03 Chevrolet Colorado, and the resitor was located under the glove compartment, where the motor blower is, the resistor is screwed to the side of the blower. hope this works for you. the resistor is usually located there.
Blower resistor is under Drivers' side of center console
where is the heater blower resistor in a 2003 Honda element
The blower resistor for a 2003 Trailblazer is located under the passenger side of the dash.
Blower motor speed resistors are generally located close to the blower motor.
The 1991 Honda accord blower motor resistor is located on the firewall in the engine compartment. The blower motor resistor will be on the passenger side of the firewall.
You have a bad blower resistor. it is located directly behind the blower motor on the passenger side of the vehicle. You must first disconnect blower motor from bad resistor. Lower and remove blower. It won't be easy but remove the screws holding the resistor, disconnect the resistor and remove it. Cost is approximately $40 for a new one.