0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is a contactor for a Central Air Unit?
The relay actuated by the thermostat which starts and stops the compressor and condenser fan in the outdoor unit.
What is the different between contactor and relay?
A contactor, as far as being used to start a motor or the like, is in essence, a relay. A coil is energized and the normally open contacts from the contactor close (normally 3 contacts for an AC motor) and the motor starts. Do I understand your question? Or are you trying to decifer the difference between the coil of a relay and the contacts of a relay?
What is the function of phase sensing relay?
A phase sensing relay monitors all three incoming phase legs at once. With the relay the operator has the ability to set the trip points in a percentage of incoming line voltage. If the voltage in any of the monitored legs falls below the operators set point the relay will trip and take the monitored device off line. If it is a motor being protected, the auxiliary contacts on the phase sensing relay will change state and its N.C. contact will open. The motor's contactor coil is in series with this auxiliary contact so with the stoppage of current flow to the magnetic contactor's holding coil, the contactor opens cutting off the supply to the motor.
What is the Difference between a magnetic starter And a contactor?
Motor starter usually refers to the complete assembly, including enclosure, contactor, control transformer (if any), overloads, fuses (if any), etc. A contactor is really just an overgrown relay, and is just one component of a starter. That having been said, many folks use the two terms somewhat interchangably. So someone who says starter may mean contactor, and vise-versa. Go figure.
Can a 120V solid state relay stands 240V?
No.If you are looking of a relay that will allow 240V, many suppliers sell a SSR that will handle up to 280V AC. Most are triggered by 3-32v dc.Just google: solid state relay OR solid state contactor
How do you wire a relay to a motor contactor?
One way is to use the auxiliary contacts on the motor contactor to close a separate source supply to drive an auxiliary relay.
Can you replace an 3 phase solid state relay with a contactor on a 3 phase heater?
Not without other modifications. The circuits used to turn the solid state relay on will not be suitable for turning a contactor on.
What is the part of the contactor that gets magnetized by the relay coil is called what?
Shading pole. It helps to stop the relay from chattering.
How relay is used to control induction motor?
If you want to control induction motor using a control relay give neutral directly to the one point of coil of relay & one point of coil of contactor then give control supply through push button to second point of coil of relay. use one NO point of relay and give supply to coil of contactor. and also use one NO of contactor for holding the contactor & take OFF (NC) in the starting to stop motor after complition of work. It is jut like an Direct On-line starter.
What device is the only load in the control circuit of a condensing unit?
I think that would have to be some relay or contactor coil for a fan, compressor or relay contacts.
What is a magnetic contactor protection device?
Contactors have both power and auxiliary contacts. We use the auxiliary contact to control magnetic system of contactor. When a heater , relay or a key warn the contactor it is energized and by the typical magnetic interaction it opens its closed power contacts.
If condencer contactor goes out...will it stop blowing cold air?
this is most likely a relay under the hood.
How does a normally closed contact work?
De-energize it and note the position of the contacts.
What is a electrical contactor for?
An electrical contractor does the wiring for homes and businesses. They install the wiring and electrical components needed to run electricity. The question asks about a contactor, not a contractor. A contactor is a type of heavy duty electrical relay for using smaller voltages to control much larger voltages.
How does an auxiliary contact work?
The auxiliary contact is to be utilized for interlocking of another relay or contactor or indication signal from another equipment.
What is a contactor for a Central Air Unit?
The relay actuated by the thermostat which starts and stops the compressor and condenser fan in the outdoor unit.
What is the different between contactor and relay?
A contactor, as far as being used to start a motor or the like, is in essence, a relay. A coil is energized and the normally open contacts from the contactor close (normally 3 contacts for an AC motor) and the motor starts. Do I understand your question? Or are you trying to decifer the difference between the coil of a relay and the contacts of a relay?
