answersLogoWhite

0


Best Answer

Hi, for sure the temp sensor for gage is on the right hand head, close to manifold, and the other one for ECU should be close to the intake, just obver water pump.

User Avatar

Wiki User

โˆ™ 2008-10-20 16:19:47
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: Where is the coolant temp sensor and sender on a 93 Jimmy 4X4 4.3L Vortec V6?
Write your answer...
Submit
Related questions

What does a temp sensor sender look like for a 2001 gmc Jimmy?

where it the temp sensor sender located on a 2001 gmc Jimmy


Where is the coolant sensor for a GMC 2001 jimmy?

water temperature sensor located near steering colum..


Where is the fuel sensor for 96 gmc jimmy?

I don't know about the Jimmy, specifically, but the fuel sensor on most fuel injected cars are located inside the gas tank, as part of the fuel sender (pump).


Where is the location of the coolant temperature sensor in a 1995 GMC Jimmy?

Coolant temp sensors are usually located very close to the thermostat housing, so follow the upper radiator hose to the engine, it will attach to the thermostst housing and you will see the coolant sensor close by.


Will a 4.3 vortec fit in 89 jimmy?

it should


What kind of gas does a gmc jimmy take?

unleaded, 89 or higher for a vortec.


Where is the oil sensor found on a 97 gmc jimmy?

where is the oil sensor on a 97 gmc jimmy


Where is the oxygen sensor on a 1993 Jimmy with a 4.3L vortec engine and how do you remove this sensor without being a contortionist?

get the truck up on some ramps. Just behind where the two exhaust pipes "Y" together, you'll see it.Screws in from the upper side (near the floorboard) down.


What type of motor came in 1997 GMC Jimmy?

4.3 liter V6 vortec


What would not let a 1995 jimmy 4.3 vortec not get spark to plugs?

Bad coil, Bad damaged or unplugged crank/cam position sensor, bad rotor, distributer cap, faulty distributer, plugs wires


Where do you find vacuum hose diagrams for a 1993 GMC Jimmy vortec V6 4.3?

Thank You


Will the engine and transmission from a 1994 GMC Jimmy S10 SLE 4POINT3 liter vortec motor fit into a 1999 GMC Jimmy SLT?

the simple answer is YES. though, a 94 would be either a t.b.i. system or early vortec. if it is a vortec, the swap shouldn't require a p.c.m. reflash- however if your 94 is a t.b.i. you will need to change the intake and fuel delivery systems to handle the 60 p.s.i. operating pressure for the vortec engine.


Is a vortec v6 motor an option for a 1997 gmc jimmy 2dr automatic or does it come stock or did someone put it in custom?

The 1997 came standard with the 4.3 Liter Vortec V6.


What is the normal fuel pump pressure for a 1998 jimmy with Vortex system?

57 - 61 psi for the 95 jimmy 4.3 vortec so it is probable the same


Where is the knock sensor located on 2000 gmc jimmy 4x4 v6 vortech engine?

2000 jimmy 4.3ltr v6. were is the o2 sensor bank 1, sensor 3


Changing the camshaft positioning sensor on a 98 GMC JIMMY?

To change the camshaft positioning sensor on a 98 GMC Jimmy you need to first locate it. The sensor is located within the distributor. Next, unbolt the old sensor and replace with a new sensor.


Gurgle noise in 1995 Jimmy?

Low engine coolant or ineffective coolant. Add or replace anti freeze


What is horsepower of a 4.3 liter V6 vortec engine?

I believe 190 hp. That's what my 99 Jimmy with a vortec 4.3 is estimated at. The basic 4.3 Vortec V-6 was rated at 160 or 165 hp. Starting in 1994 an "enhanced Vortec" 4.3 V-6 of 195 HP became available alongside the basic version.


How many quarts of oil does a 1997 GMC Jimmy 4.3 liter vortec engine need?

5 quarts


What is the firing order for a 4.3 liter Vortec in a 1995 GMC Jimmy?

The firing order for the 4.3L engine is 165432


Where is the crankshaft sensor for a 1995 gmc jimmy?

The crankshaft sensor is by the crankshaft pullie (the balancer)


You have 94 s-10 blazer 4.3 and a 94 gmc jimmy with a vortec The 94 gmc vortec is bad Can you remove the fuel injection from it and sit on the non vortec engine What changes to make it work?

you would need to change the cylinder heads also.See link below


How do you test a crankshaft position sensor on a 1996 jimmy blazer?

To test a crankshaft position sensor on a 1996 Jimmy Blazer, use a CKP sensor to test for voltage output. Compare the results to manufacturer specifications.


Where on a 1994 Chevy blazer is the oxygen sensor located bank one sensor one?

where is the oxygen sensor in a 1995 gmc jimmy


What v8 engine can replace 2002 GMC Jimmy 6 cylinders?

The v8 engine 2002 GMC Jimmy 6 cylinders can be replaced with the GM Vortec 4200 straight-6 engine.