0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Gearbox filler point on a mk6 Ford Fiesta?
Hi Remove plastic covering where the gear change cable go. You'll see the oil level / filler plug on the gearbox casing. 8mm hex head to loosen. Have fun
When was the Fiat Ducato first produced?
The first Fiat Ducato was produced in 1981. Since then more than two point four million Fiat Ducato vehicles have been produced. It is the most common motor home in Europe.
What is a road ranger gearbox?
a gearbox with 9 to 18 gears that you use your splitter and you have to rev to a certain point to change gear and double clutch.
Where is the gearbox oil filler point on a 1998 1.00 Micra?
Re-filling your 1898 1.0 Micra gearbox is achieved by removing the speedometer drive cable from the rear of the gearbox adjacent to the startermotor solinoid, it is held in place by 1 x 10mm bolt.(It is tricky to get access to) Re-fill with 3.3 litres of fresh 80W90 gear oil after draining, and replace the speedo drive cable. Some 1998 onward models already changed to a different filler plug located much lower down in the gearbox housing and far easier to locate and access. It can be recognised as a round plug requiring a 3/8 inch square drive ratchet wrench to remove / re-tighten. Similar looking to the drain plug which requires a 1/2 inch square drive ratchet wrench to release and re-tighten. It is located toward the front of the engine about 4 inches from the bottom edge of the gearbox close to the drain plug.
What is the melting point of stainless steel welding filler rod?
2550 degree Fahrenheit
Characteristic of soldering iron?
Soldering iron is characterized by having the melting point of the filler metal.
Now that you have automatic cars what is the point of a manual car?
Manual gears are more versatile than an automatic gearbox
How is Brazing done?
It is done with applying heat and adding a filler metal. The filler, which has a lower melting point than the metals to be joined, is fed into the joint as the parts are heated. It is similar to soldering but at a much higher temperature.
Want to change gearbox oil cant seem to find the refill point help me plzzzz?
Depends on make and model car and type of trans.
How do you locate the filler and drain plug for the transmission on a Mitsubishi galant?
If an auto transaxle, the filler tube is on the left side of the engine (from front) tust under the battery tray, down close to the fenderwell. It has a a pull-out dipstick. The dain plug is under the engine on the back side of the t-a housing. If a manual t-a, the filler and drain plugs are both on the bottom side of the t-a housing. The lower point is the drain and the upper plug is the filler. A squeeze-type container will be required to fill if an electric or pump-type is ot available.
What is Brazing hearth?
brazing is joining of two metals by using filler metals.to melts the filler rods only which temperature is above the melting point (>450c).initially flux metal is used to avoid the oxidation ....this process is very strongly than soldering method ...weaker than welding method..
How do you change the clutch on a landrover discovery?
Well, I thought I'd have a go! Haynes recommend you take the engine out, but after seeing a post on LR4x4 I thought i'd follow it and move the gearbox back. I started the job a week ago, clutch is now in but I cannot get the gearbox back in place. So my answer is....... get someone else to do it! Yeah ive done 3 and always taken engine out from the point of view of lineing the engine/gearbox back up again. also when you change the clutch plates after removing engine make sure you renew the clutch fork. that is loacated in the gearbox housing, you will see it when you take the engine out.
