Best Answer

Normally attached to the distributor (not the cap) on the side. Takes a special tool to remove it. Available at the parts store.

User Avatar

Wiki User

โˆ™ 2006-02-28 15:13:08
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Where is the ignition control module on a 1987 Ford F250?
Write your answer...
Related questions

Why does ignition control module fuse on f250 keep blowing?

Short in the circuit, the circuit is overloaded, or you are installing too small a fuse.

Where is the ignition control unit on a 1990 F 250 is there one?

don't know about the particular year. on my 95 F250, the ICM is located on the driver's inside fenderwell, underneath the Powertrain Control Module. hope that helps.

What does the body control module do on f250?

controls all of the electrical systems not related to the motor

F250 1989 no spark all new plugs new coil coil wire good what can it be?

I would look first to the rotor, and then maybe at the module check the ignition module

Where is the F250 module located on the truck?

You need to specify which module.

Where on a 92 f250 is the ignition module and is it also the coil or is the coil separate?

They are separate The ignition module is on the drivers side fender usually mounted in the middle of an aluminum box with fins on it. The coil is easy to find just follow the center wire on the distributor and you'll find it.

What does the power train control module do on a ford f250?

I have a erorr code P0603 and P1211 and it said Powertrain Control, Keep alive memory Erorre Can you help me?

Where is the fuel injector control module located on a 2004 f250?

driver side valve cover between coolant jug and turbo.

Where is the 4x4 control module located for 2002 f250?

it is located above the heater core trap door behine the glove box.

What part is the BFN14-12 or 1828565C1 unit in the Ford f250 diesel power stoke wiring?

glow plug control module

Is 1977 F250 PU with 351 Windsor Ignition is dead Is there an in line fuse for ignition Is there an 'ignition module'?

the inline fuse for the ignition requires remove the bezel panel and the gauge panel from dash. trace the red wire up and to the top rear right of the dash you'll find a lump in the wire.

How do you replace ignition coil on F250 V8?

I'll include a link to a video below that will show you how to repair the ignition coil in your Ford F250 or F350. hope this helps.

What is ford 5.8 ignition coil restance?

What is there stance specifications on an ignition coil for a ford 5.8 f250

What is the Wheel size for 1987 ford f250?

16 "

Why does your 2000 F250 start without the key?

The ignition lock seems to be broken.

Where is the computer module for a 95 f250 located at?

Behind your emergency brake release handle

Where is the voltage regulator on a 1987 f-250 with a 460?

voltage regulator on 1987 ford f250

Where is the transmission control module location of a 1989 f250 with the 7.3 liter diesel.?

behind the radio from what im readding ill know tomorrow when i pull mine and go to the junk yard to find another

Where is the Powertrain Control Module - PCM in a 96 Ford f250 7.3?

The PCM is bolted through the fire wall. Behind the parking brake. You will need to remove the driver side inner fender liner to get at it.

Where is the fuel injector module for 2000 ford f250 7.3 diesel located?

On the drivers side inner fender

Where is the speed control deactivation switch on 1999 Ford F250?

speed control switch inside trans

Why would the ignition switch run start feed fuse blow on a ford f250?

you may have a short in the ignition swith get test checked, a steering column specialist can do this in a couple of minutes

When you start your 87 f250 and let off the switch it cuts off?

Sounds like ignition switch needs replacement

What is the ignition timing on a 1975 ford f250 with a 390 motor?

Good rule of thumb around 6 to 8 btdc

Will 1983 F250 rims fit on a 1990 F250?

NO! Even though they look the same, the center hole on 1987 up 8 hole rims are bigger than your 1983 rims.