0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Which position is number 1 on the distributor cap of a 1995 Chevy Z71 350?
#1 will be the first hole past the cap's mounting screw on the left side of the distributor, going clockwise.
Where on the distributor cap does number 1 plug wire go on a 1970 ford 302?
# 1 position on the distributor cap faces to the REAR and slightly towards the drivers side Maybe, or any one of the other 7 spots. A distributor can be put in several different spots as far as which point on the distributor is number 1. If you have not had the distributor out of the engine, take number one plug out and hold your finger over the hole and crank the engine by hand until you feel the compression building. Watch the crank shaft pulley for the timing mark and when it gets to the pointer, that is number 1. Look under the distributor cap to see which one the rotor is pointing at.
What hole on the dist is 1?
As you face the engine the first spark plug wire on your left is connected tot he first cylinder. Trace it back to the distributor and you will have the proper hole. If you have no wires connected then it is usually positioned at about 1 oclock as you face the distributor. (assuming the distributor is properly positioned)
Where is number 1 on distributor for 1983 Dodge 360?
# 1 on the distributor cap faces to the FRONT / CENTER
Where is mounting bolt for distributor on 305 1993 Chevrolet v8?
There is a tapped hole next to the distributor hole in the intake manifold.
Where is number 1 on the distributor cap of a 1994 d15b7 Honda?
Number 1 on the distributor cap is the top post closet to the firewall. Looking at the distributor cap it would be... top row 1-3 bottom 2-4
How do you set timing on 1999 Chevy Tahoe 5.7l?
if you have removed the distributor,you will need to bring number one cylinder up to TDC,where both tappet are closed and number one cylinder in all the way to the top of the cylinder,with the number #1 plug out you can verify it is!after you have that done,then look at the distributor cap,most caps on top are marked where number one plug wire should go,drop the the distributor down in the hole moving rotor to point where number # 1 cylinder in at on cap close as you can,you may have to turn oil pump shaft down in distributor hole,use a screw drive flat blade a long one to turn slot to correspond with distributors rotoe to place on number one ,then set distributor in hole where it will go down in slot to line up with where the rotor points to number one on cap,then you should be close to time,this should get you where the motor will start,by adjusting the position of the distributor by turning a little each way,but you will need to have a scan tool placed on it to get it to the closes point where the check engine light will go out,or to be reset!
Where on distributor cap for a 79 gmc350 is number one?
Number 1 cylinder is located drivers side, front of engine. Remove all spark plugs, rotate the engine by hand until # 1 piston is at TDC on the compression stroke. There are several ways to find this out. One way to find #1 on the distributor is to place your thumb over #1 plug hole and rotate the engine until you feel it pushing at your thumb. Now place a long screwdriver into the plug hole and touch the piston, rotate very slowly until the piston reaches the top. Remove the distributor cap and the rotor will now be pointing to #1.
Which wire is number 1 on vortec 4.3 distributor cap?
where is number one on a vortex 4.3 v-6 distributor cap
How does a 460 distributor cap go on?
The marked # 1 position on the distributor cap faces towards the REAR
What goes in distributor hole on 6.2?
The dristibutor
Where on the distributor cap does number 1 spark plug wire go on a 1991 ford 5.0?
The distributor cap should have the number 1 marked on it. The distributor cap is installed with the # 1 position facing the engine , slightly towards the drivers side of the engine
