answersLogoWhite

0

On a 1995 Mercury Mystique :

If it is the same as the 1996 model , the fuel pump shut off switch ( inertia

switch ) is located in the drivers footwell behind the kick panel ( there is an

access hole )

* the kick panel is the interior trim panel , in front of the front doors , by the

persons feet

User Avatar

Wiki User

12y ago

What else can I help you with?

Related Questions

Where is the safety switch to the Mercury mystique?

In the ( 1997 ) Mercury Mystique : The fuel pump shut off switch ( inertia switch ) is in the drivers footwell behind the kick panel ( there is an access hole ) * it's near the inside hood release *


How do you remove the drivers side airbag on a 1996 Mercury Mystique?

Don't do that!It's a major mistake to do that!The airbag is a safety device.


What does the safety switch on the mercury mystique do?

It prevents the starter from turning when the car is NOT in Park or Neutral, so that cars don't accidentally take of when starting.


How do you take the dashboard off 98 mercury mystique?

To remove the dashboard from a 1998 Mercury Mystique, start by disconnecting the battery to ensure safety. Then, remove the screws and clips securing the dashboard, which are typically located around the instrument panel and under the trim. Carefully detach any electrical connectors for gauges and controls, and gently pry the dashboard away from the mounting points. Make sure to keep track of all screws and connectors for reassembly.


Where is the cruise control fuse and relay in a 1998 mercury mystique?

In a 1998 Mercury Mystique, the cruise control fuse is typically located in the fuse box under the dashboard on the driver's side. The relay for the cruise control is usually found in the engine compartment fuse box. To access these components, you may need to refer to the vehicle's owner's manual for specific diagrams and locations. Always disconnect the battery before working on electrical components to ensure safety.


Where is the location of the fuel pump safety cutoff on 87 ford aerostar?

located in the jack storage compartment inside the back of the van!


Why does the OD light flash and then the check engine light come on a little later on a 1999 Mercury Mystique?

May also want to check the module ontop of the transmission, it's located next to the battery, I'm not sure if the part's correct name is a neutral safety switch.


Where is the Ignition Control Modular on a 1998 Mercury Mystique 2.5 liter engine?

The Ignition Control Module (ICM) on a 1998 Mercury Mystique with a 2.5-liter engine is typically located near the engine's right side, mounted on or near the intake manifold. It is often positioned on the passenger side of the engine bay, close to the firewall. To access it, you may need to remove some components or covers, as it can be somewhat tucked away. Always refer to a service manual for specific guidance and safety precautions when working on the vehicle.


Where is the neutral safety switch on a 1994 Mercury Villager located?

It might be the transmission range selector


Were is Mercury located?

You can find mercury inside a glass thermometer, if it is old and maybe a bit out of date. Don't break it though to get the mercury out... unless your in a lab and you have all the safety equipment


How do you change the cooling fan on 1998 mercury mystique?

To change the cooling fan on a 1998 Mercury Mystique, start by disconnecting the battery to ensure safety. Remove the radiator support cover and the bolts securing the fan shroud to access the fan. Disconnect the electrical connector and any hoses that may obstruct removal. Finally, unbolt the fan from the shroud, replace it with the new fan, and reassemble everything in reverse order.


How do you change ignition switch on 95 mercury mystique?

To change the ignition switch on a 1995 Mercury Mystique, first disconnect the negative battery terminal to ensure safety. Remove the steering column covers, typically held by screws, to access the ignition switch. Disconnect the wiring harness from the old switch, remove the retaining screws, and replace it with the new switch. Finally, reassemble the column covers and reconnect the battery.