0
Where should submersible pump be placed or installed in ground water well?
Wiki User
∙ 12y ago
There are a few parts to an answer. How deep is the water in your well? Is there sludge or sediment at the bottom of the well? How deep is this and how much is clean water? How long is your pump? How long is the motor housing?
I just placed a 70cm pump, motor 35cm, in 250cm if clean water. 20cm of sludge. The bottom the motor housing was placed about 40cm above the sludge which means there is about 75 cm of clean water below the water inlet and 175cm of water above the pump. It will take many years for the sludge to rise and even in low water periods I should stay in operation.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
When placed in the ground will a pressure treated 2X4 last as long as a pressure treated 4X4?
If the pressure treatment is identical, theoretically they should perform equally.
Where should the Doctype be placed on the webpage?
A doctype is a header, so it should be placed at the top of the webpage. When writing HTML for a website, it should be placed directly above the tag.
How far apart should screws be placed in a metal roof?
how far apart should screws be placed ina metal roof
Pump-down system should be installed in which direction?
South
Should limits be placed on robots?
its up to you.
How can you find your submersible water well pump if there is no pipe out of the ground?
There has to be a casing for the pump to be in. There should be something showing above ground. How is the power run to it, does that point you in a direction? Where is the water tank, where does the line coming in point to?
Where the switch can be placed?
Wall switches should be 48" from the floor to the top of the switch box. They should never be placed behind a door. They cannot be installed within 3' of a bathtub or shower. Other than that they can be placed anywhere. For the most part they should be installed in the room where the light is located and not outside that room if possible. Use common sense.
What is the minimum depth in feet that a grounding rod must be driven into the ground?
Ground rods in the U.S. on a residential home are 8 foot long and are driven 8 feet into the ground. The top of both ground rods should be flush or just under the surface. One ground rod is placed directly under the meter base and another one is placed 6 feet to either side. They are connected together and grounded to the meter base with the correct size ground wire based on the amperage of the serviced being installed.
When traveling with empty forklift how should the blades be placed?
1 foot above ground.
What is the minimum distance a ground fault device should be installed near a water source?
15 feet.
Wiring diagram well water?
If you mean a pump wiring diagram, it depends what kind of pump you have, submersible or Jetpump. Both are very simple wiring and don't need a diagram. Both should be installed by a qualified well technician.
How can you remove submersible pump which is struck in bore well 300 feet below ground?
It should not be stuck in well. If you are 300 feet, it is going to take a lot of pull to get it out. You might just think it is stuck?
Where should a Buddha statue be placed in a apatment?
Somewhere respectful, not close to the ground, where you will not point your feet towards it.
Why is the rain gauge buried in the ground?
The rain gauge should be buried in the ground to prevent it from being toppled.The rain gauge should be placed in the buildings as the heat causes the water collected to evaporated.
Are all aquarium heaters submersible?
There should be a line indicating how far they go down in the water
How much sand should be installed under a 22 x 52 above ground pool?
In the instructions it says not to use sand or it voids the warranty
Should one or two electrical service ground rods be used on a service distribution?
In Canada the requirement for grounding purposes calls for two 5/8" x 10' ground rods placed 10' apart. If rocky ground is encountered, then a grounding plate can be installed. The grounding plate dimensions are 10" wide x 16" long x 1/4" thick. They are galvanized coated and must be buried 24 inched below grade.
