answersLogoWhite

0

No Mercury compound has a boiling point as high as this.

User Avatar

Wiki User

10y ago

What else can I help you with?

Related Questions

Whats the spark plug gap on 2002 Honda shadow 1100c?

.030 - .035


What is the spark plug gap on a 1987 Honda shadow 1100c?

THIS IS FROM CLYMER REPAIR MANUAL. NGK BP8ES COLD PLUG, NGKBP7ES PLUG GAP .031-035


How do you set the timing on Honda V65 Magna 1100c 1983?

To set the timing on a 1983 Honda V65 Magna 1100cc, first, ensure the bike is on a level surface and the engine is cool. Remove the timing inspection cover to expose the timing marks on the rotor and the stator. Rotate the engine to align the timing mark on the rotor with the T mark on the stator at the appropriate RPM (typically around 1,500-2,000) while adjusting the timing using the advance mechanism until the marks are aligned. Finally, recheck the timing after securing everything back in place to ensure accuracy.


How much energy is required to change a 40 g ice cube from ice at 10C to steam at 1100C?

Trick or Treat! Early chemical analysis used melting & boiling points (temperatures) to establish the purity of samples. As temperature rises in a pure substance, the change in temperature will stop rising in the substance until the phase change is complete (solid [ice]=>liquid [water] & liquid [water]=>vapor [steam]. Therefore the [energy] heat would be the sum of raising the mass of ice to it's melting point plus the heat necessary to make the change of state plus the heat to raise the temperature of water to it's boiling point plus [the trick] the heat required to raise the temperature of steam to 1100 degree C. but gases [vapor] temperature involves changes in pressure (PV=nRT) so unless it is in a sealed container, the water would boil away never reaching the temperature. If in a sealed container there would be the dependent variable of container volume,


What chemicals make up clay?

depending on the type of clay, it will contain the following compounds: Silica (oxides and sulfates) Alumina (oxides) Various Metal salts Various Organic materials a typical Iron (red ) clay is composed of: Silica Alumina Feldspars (silica oxide and Monomirellite) Iron Oxide Some clays may contain heavy metals, such as Lead,cobalt,maganese,boron, or other metals depending on it's source. all of these clays are really just finly ground dirt. and have no scructutural strength unless "vitrefied" that is, heated until near it's Melting point, at wich all the individual partivcles melt into one another and create a single peice,(much like the rock it came from) these tempratures range anywhere from 1100C to 4500C (actually is a bit more complicated that that) another type of "Clay" is the acrylic and latex based "plasticine" modeling compounds. these consist of an acrylic base A plasticizer (such as mineral oil), Aniline and other chemical dyes, Silica dioxide, Calcium Carbonate, and many other materials. these are typically non fired, or in the case of firmo and sculpy, they can be "hardened" at 400-600 degrees. other modeling compounds can be made from starch, or other organic materials. ( a good modeling compound for kids is 4 parts AP flour , 1 Part table Salt, and 1 1/4 part water . this compound can be cooked in a 300 degree oven for 1 hour, to create surprisingly hard objects (safe and edible (yuk)) to make ornaments and small items.


What is bone china made of?

Bone china is made of 50% bone ash, & 25% each of china clay and china stone. It is combined with water to make a slurry, which is then fashioned into cups, saucers, plates and so on. The pieces must be fired in a kiln at high degrees of heat (1100c to 1250c) for the china to become hard and strong. It is the bone (usually animal bone, cleaned of all meat and glue) that gives the china its transparent whiteness. The ingredients of bone china are china clay, china stone, silica, alumina, alkalies, lime and bone ash. It is fired at high of 2,300 to 2,500 degrees Fahrenheit. In the best grades of English bone china, 50% or more of the body consists of refined bone ash prepared from specially selected animal bones which are reduced to a fine powder by heat. The bone is mixed with the finest china clays and highest quality Cornish stone. Specially skilled workers are needed in the manufacture of bone china and the best and most highly skilled in the world are found in the pottery district of England.


Melting point of Phenol formaldehyde?

Because phenol formaldehyde is a resin it is usually a mixture of chain lengths and cross linking. For this reason, you would not expect it to have a fixed melting point - rather it would usually have either a melting point range or a decomposition temperature (depending on the structure). As an example, the company Polyols and Polymers lists the melting point range of their POLYTONE PF 201 product as 700C-850C while their POLYTONE AP 132 product has a "softening point" of 970C-1100C but no melting point. Bakelite - which is one of the many types of phenol formaldehyde resin - is a thermosetting plastic which has no melting point; it has a decomposition point. As an example, the Bakelite manufactured by Jiacheng-Chem Enterprises Ltd. has a listed decomposition point range of 240~ 280°C. Again, because it is a mixture of polymer sizes and degree of cross linking, it doesn't have just one fixed temperature; it has a range over which the many different molecules will decompose. The temperatures under which phenol formaldehyde will melt, soften, or decompose are also affected by the amount of residual monomers still present in the polymer matrix.