0
Which command or commands will configure a catalyst 2950 switch with the IP address 192.168.10.2?
Wiki User
∙ 11y ago
ALSwitch(config)# interface vlan1
ALSwitch(config-if)# ip address 192.168.10.2 255.255.255.0
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Which of these commands do you use to configure a router for virtual terminal line address filtering?
line vty access-class
What commands are used to configure a serial interface for the DCE?
interface serial x/x ip address x.x.x.x x.x.x.x no shut clock rate xxxxxxx end
How do you configure ip address in fedora 15 terminal?
step 1):- open terminal step2):- setup step3):-and now u can go in ip address configure. step4):-now u can easily configure ip address
When would you configur a GRE tunnel?
To configure a GRE tunnel, create a tunnel interface by issuing the interface tunnel command from the global configuration mode. To configure the tunnel source and destination, issue the tunnel source {ip-address | interface-type} andtunnel destination {host-name | ip-address} commands under the interface configuration mode for the tunnel.
How do you configure a network card in Linux?
That depends very much on what you want to configure with it. Many aspects, such as MAC address and IP address, can be configured with the ifconfig command.
How can you give private ip on a LAN?
The same as a public IP. Your choices are: (1) assign an address manually, and (2) configure the computer to get an IP address automatically from a DHCP server.The same as a public IP. Your choices are: (1) assign an address manually, and (2) configure the computer to get an IP address automatically from a DHCP server.The same as a public IP. Your choices are: (1) assign an address manually, and (2) configure the computer to get an IP address automatically from a DHCP server.The same as a public IP. Your choices are: (1) assign an address manually, and (2) configure the computer to get an IP address automatically from a DHCP server.
What mode must be in to configure IP address on a Cisco router?
interface mode
Starting at the enable mode prompt what commands would you type to configure IP address 192.168.1.1 on interface E0?
I will show the commands, together with the prompt, assuming the router name has not been changed. A subnet mask is also required; I will provide one. ^Z is Control-Z, used to exit configuration mode quickly: Router>enable Router#configure terminal Router(config)#interface E0 Router(config-if)#ip address 192.168.1.1 255.255.255.0 Router(config-if)#^Z Router#I will show the commands, together with the prompt, assuming the router name has not been changed. A subnet mask is also required; I will provide one. ^Z is Control-Z, used to exit configuration mode quickly: Router>enable Router#configure terminal Router(config)#interface E0 Router(config-if)#ip address 192.168.1.1 255.255.255.0 Router(config-if)#^Z Router#I will show the commands, together with the prompt, assuming the router name has not been changed. A subnet mask is also required; I will provide one. ^Z is Control-Z, used to exit configuration mode quickly: Router>enable Router#configure terminal Router(config)#interface E0 Router(config-if)#ip address 192.168.1.1 255.255.255.0 Router(config-if)#^Z Router#I will show the commands, together with the prompt, assuming the router name has not been changed. A subnet mask is also required; I will provide one. ^Z is Control-Z, used to exit configuration mode quickly: Router>enable Router#configure terminal Router(config)#interface E0 Router(config-if)#ip address 192.168.1.1 255.255.255.0 Router(config-if)#^Z Router#
What protocol can configure a computers ip address and subnet mask automatically?
With the Windows Command Prompt, you can enter the command "ipconfig" and then configure everything you just stated in your question.
What should you do if Router R2 is configured properly and all interfaces are functional Router R1 has been installed recently Host A is unable to ping host B?
Configure a static route on R1 using the IP address of the serial interface on R1. Configure a default route on R1 with the exit interface Fa0/0 on R1. Configure a static route on R1 using the IP address of S0/0/0 on R2. Configure a default route on R1 using the IP address of Fa0/0 on R2.
How do you set up your ip address for a webserver?
First you have to configure your NIC card, preferably with a static IP address. Then, tell the webserver software which port and which address to listen on.
What information is needed to configure a NIC?
i.p address, sub-net mask and default gateway
