0
What else can I help you with?
In a 2003 Bonneville which of the hoses to the water pump is the heater inlet hose?
On a 2003 Bonneville, the hose to the water pump that is the heater inlet hose is the top hose coming from the radiator. This is also the hose that holds the thermostat.
What heater core hose goes to the water pump on a 1986 Chevy Caprice?
Generally, the upper heater hose leads to the water pump.
Heater core inlet hose?
The return hose for the heater core generally leads back the the water pump. The inlet for the heater core comes from the engine.
What is the layout for radiator hoses on a 1990 Chevy Astro van?
one large hose from bottom of radiator to side of water pump. other large hose from thermostat housing to top of radiator. one heater hose from water pump to heater core, I think this one has a Y in it if there is a rear heater other heater hose from heater core to somewhere on top the engine. If there is a rear heater, its return hose goes to a fitting on the radiator.
How do you remove the heater hose that connects to the water pump on a 1995 Chevy Suburban?
Cool the heater hose and then gently take it off
Can a pocket hose drain a water heater?
Yes, a pocket hose can be used to drain a water heater, provided it has the appropriate fittings to connect to the drain valve of the heater. However, the flow rate may be slower compared to a standard garden hose, depending on the diameter and length of the pocket hose. It's essential to ensure that the hose is rated for hot water and can handle the temperature without damage. Always take necessary safety precautions when draining a water heater.
How do you fix the heater coil for a 2000 Chevy s10 blazer?
If the heater core is plugged you can try flushing it out. Disconnect the two heater hoses from the engine, connect a garden hose to either hose leading to the heater and gently turn on the water, gradually open water valve all the way until water runs clear then switch water hose to opposite heater hose and repeat. If the heater core is leaking and needs replacement I would strongly suggest purchasing a shop manual to walk you through the job of replacing the heater core. This is not a simple job.
Does the top or bottom heater hose from the firewall go to the water pump on a 1991 Dodge Dakota V6?
"Does the top or bottom heater hose from the firewall go to the water pump on a 1991 Dodge Dakota V6?" The top heater hose from the firewall goes to the water pump and the bottom hose from the firewall goes to the top of the block where the temperature thermostat housing is located.
How can I effectively drain a water heater without a floor drain?
To effectively drain a water heater without a floor drain, you can use a garden hose to siphon the water out. Attach the hose to the drain valve at the bottom of the water heater and run the other end of the hose to a lower area where the water can safely drain. Open the drain valve and let the water flow out through the hose. Make sure to turn off the water heater and let it cool down before draining to avoid burns.
How can I effectively drain a Rheem water heater?
To effectively drain a Rheem water heater, follow these steps: Turn off the power or gas supply to the water heater. Connect a garden hose to the drain valve at the bottom of the heater. Place the other end of the hose in a drain or outside. Open the drain valve and let the water heater drain completely. Close the drain valve and remove the hose once the water heater is empty. Turn the power or gas supply back on and refill the water heater before turning it back on.
What are the best water heater options for a garden hose?
The best water heater options for a garden hose are electric tankless water heaters or portable propane water heaters. These options provide efficient and reliable hot water for outdoor use.
How do you clean a heater core on a 1998 chevy s-10?
This is how I do it, loosen the radiator petcock and drain down the cooling system. Remove both heater hoses from the engine side only. Fabricate a fitting that fits into the heater hose and also attaches to a garden hose. Attach the fitting to either one of the heater hoses and the garden hose. Direct the remaining heater hose down to the floor possibly into a large container. Gently turn on the water and gradually increase the water flow until it is on full. Notice the crud that comes out. Now reverse the flow through the heater core by swapping the garden hose to the other heater hose and repeat process until the water runs clear. Reattach the heater hose to the engine and refill the cooling system with fresh coolant.
