Some well known examples are a motor, relay, solenoid valve, electromagnet, transformer, lamp ballast, and an ignition coil. However, in electronics, even a piece of wire can be considered an inductive load because it has the property of inductance. An inductor is a device that produces a magnetic field while an electrical current is passed though it.
An electrical motor is an example of an inductive load. Solenoids and contactor coils are also in this category of induction dependant devices.
probably an eighteen weeler with an oversised load going down the road.
non- inductive load is without motor and transformer loads are non-inductive load, purely resistive are capacitive loads phase angle is unity are leading PF A non-inductive load is a load whose current does not change instantaneously.
Resistance load it means there is passive load to impede current flow. Inductive load means there is a coil as a load while still a passive it has its own characteristics which differs from a resistive load which is linear while inductive is not linear load
There is no problem using a generator to run more inductive load so long as the generator capacity can supply the needed power to the inductive loads. The inductive loads should not be switched on at the same time but there should be a little delay before another load is switched ON as inductive loads draw more power at start ON. The power factor of the inductive loads also affect the generator, hence for safe operation a power factor that is approaching 1 is desirable. Ogu Reginald Ekene
The phase angle is defined as the angle by which the load current leads or lags the supply voltage.For a purely-resistive load, the phase angle is zero, because the load current is in phase with the supply voltage.For a purely-inductive load, the phase angle is 90 degrees lagging.But few loads are either purely-resistive or purely-inductive; typically, most loads are resistive-inductive. This means that, typically, the phase angle lies somewhere between zero and 90 degrees.
The actual energy consumed in load is inductive load
non- inductive load is without motor and transformer loads are non-inductive load, purely resistive are capacitive loads phase angle is unity are leading PF A non-inductive load is a load whose current does not change instantaneously.
non- inductive load is without motor and transformer loads are non-inductive load, purely resistive are capacitive loads phase angle is unity are leading PF A non-inductive load is a load whose current does not change instantaneously.
Resistance load it means there is passive load to impede current flow. Inductive load means there is a coil as a load while still a passive it has its own characteristics which differs from a resistive load which is linear while inductive is not linear load
There is no problem using a generator to run more inductive load so long as the generator capacity can supply the needed power to the inductive loads. The inductive loads should not be switched on at the same time but there should be a little delay before another load is switched ON as inductive loads draw more power at start ON. The power factor of the inductive loads also affect the generator, hence for safe operation a power factor that is approaching 1 is desirable. Ogu Reginald Ekene
The phase angle is defined as the angle by which the load current leads or lags the supply voltage.For a purely-resistive load, the phase angle is zero, because the load current is in phase with the supply voltage.For a purely-inductive load, the phase angle is 90 degrees lagging.But few loads are either purely-resistive or purely-inductive; typically, most loads are resistive-inductive. This means that, typically, the phase angle lies somewhere between zero and 90 degrees.
A load of any type,,,inductive or capacitive , would effect the circuit even if THOSE "loads" had no load on them. They would still have a load effect on the circuit they are connected to.Answer'Under no-load conditions' means that no load is connected to the supply. So your question doesn't make sense!
water heaters electric stoves toasters space heaters incandescent lights are resistive loads a/c and fans iceboxs and anything with a motor is inductive Type your answer here...
Any devices that have coils of wire in there manufacture can be classed as inductive loads. e.g. motors, solenoids and contactor coils are a few. Example of resistive loads can be baseboard heaters, filament light bulbs, toasters and stove top elements.
Induction motor by design is inductive load. Hence the PF tends to be lower
The actual energy consumed in load is inductive load
Inductive since it has a motor with windings.
what would be the phasor diagram of inductive load