0
Which switch interface would an administrator configure an IP address so that the switch can be managed remotely?
Wiki User
∙ 10y ago
vty 0
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
What is term for the hardware coded address found on an interface?
mac-address
How devices get their MAC or IP address.?
A device or computer gets their MAC address from their Network Interface Card (or NIC). This is not something that a user is able to change (See discussion as to why you can change your MAC address). However an IP address can be statically assigned to you which means a network administrator has physically typed out what your IP address and subnet mask is. Another way to get an IP address is through Dynamic Host Configuration Protocol, or DHCP as it is most commonly known as.
What method should be used when applying IPv4 addresses to router interfaces on a network?
When applying IPv4 addresses to router interfaces on a network, you would manually configure predictable addresses. For example, the lowest or highest address of the local subnet, on each particular router interface.
Which IP address can be assigned to an Internet interface?
172.16.200.18
Which description is true regarding the operation of dhcp?
if an address conflict is detected, the address is removed from the pool for an amount of time configurable by the administrator.
What mode must be in to configure IP address on a Cisco router?
interface mode
Which set of commands will enable a network administrator to remotely manage a LAN switch?
Switch(config)# ip default-gateway 192.168.1.254Switch(config)# interface vlan 1Switch(config-if)# ip address 192.168.1.1 255.255.255.0Switch(config-if)# interface fa0/1Switch(config-if)# switchport access vlan 1
When would you configur a GRE tunnel?
To configure a GRE tunnel, create a tunnel interface by issuing the interface tunnel command from the global configuration mode. To configure the tunnel source and destination, issue the tunnel source {ip-address | interface-type} andtunnel destination {host-name | ip-address} commands under the interface configuration mode for the tunnel.
What commands are used to configure a serial interface for the DCE?
interface serial x/x ip address x.x.x.x x.x.x.x no shut clock rate xxxxxxx end
What should you do if Router R2 is configured properly and all interfaces are functional Router R1 has been installed recently Host A is unable to ping host B?
Configure a static route on R1 using the IP address of the serial interface on R1. Configure a default route on R1 with the exit interface Fa0/0 on R1. Configure a static route on R1 using the IP address of S0/0/0 on R2. Configure a default route on R1 using the IP address of Fa0/0 on R2.
Which command or commands will configure a catalyst 2950 switch with the IP address 192.168.10.2?
ALSwitch(config)# interface vlan1 ALSwitch(config-if)# ip address 192.168.10.2 255.255.255.0
What must be done before a router can be accessed via telnet?
Configure an IP address on the relevant network interface and bring it up. Configure a password on at least on vty line and give the login command.
A network administrator determines that falsified routing information is propagating through the network What action can be used to address this threat?
Configure routing protocol authentication.
A network technician wants to configure an IP address on a router interface by using the ip address 192.168.1.0 255.255.255.0 command Which prompt should the technician see when entering this comman?
router(config-if)#
What ip address would the network administrator use to remotely access the switch via the use of ssh?
I depends on the manufacturer and model. 192.168.0.0 or 192.168.0.1 are fairly common, but there can be many others.
How do you configure ip address in fedora 15 terminal?
step 1):- open terminal step2):- setup step3):-and now u can go in ip address configure. step4):-now u can easily configure ip address
What is the purpose of assigning an IP address to a Layer 2 switch?
A layer 2 switch may need an IP address if the operator wishes to be able to access it without a serial cable. With an IP address, the switch can be access from anywhere with a connection to the network or an Internet connection.
