0
Which three parameters must be configured on a router in order to enable SSH?
Wiki User
∙ 13y ago
Which three parameters must be configured on a router in order to enable SSH? (Choose three.)
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Do you need to restart a router to enable port forwarding?
It strictly depends on the model. Most routers have to be restarted in order to enable port forwarding.
What is true about the parameters of a function (Python 3)?
a. Functions can have only one parameter. b. The order in which the parameters are defined matters. c. Parameters can be passed to a function in any order. d. Parameters have no order.
Is it possible to configure your router from your laptop if so how?
Yes, it's possible unless your router was configured to not allow to change settings for wireless connections (some routers have such option because of security considerations). Anyway you need to find out IP address for your router and start you favorite internet browser. You should put the IP address in the address bar and press Enter. It will bring you to the access page of your router. In order for you to access router's settings you need to know username and password for current administrator.
Where would the management IP address be configured on the switch in order to mange a Cisco swicth using Telnet?
The Management IP address will be configured on the Default Management VLAN (vlan1). Make sure to do a "no shutdown" command on the VLAN as for it is placed into the shutdown state when first configured. Also for telnet you will need to configure the Virtual Terminal Lines just as a regular Cisco Router. If more functionality is needed other than Telnet more configuration maybe needed depending on what switch is being used.
What is the firing order for Volvo 740 turbo?
on the engine block the order from the back to the front is 4321 but you will plug them in to the router like this. As the far left is 4 and the far right is 1. So from 4 on the engine to 4 on the router, from 3 to 3 on the router, then it switches from 2 on the engine to 1 on the router and finally from 1 on the engine to 2 on the router. So the router order should be 4312. Hope this will help
Benefits of wireless router?
It really depends on the type of router you get. Usually you have to pay a little bit more in order to get a router with firewall protection.
How is a netgear router configured?
Have trouble configuring your Netgear WNR2000 router? We're going to give you all the information you need to set up your Netgear router with the system here, so please read on. The Netgear WNR2000 Router enables high-speed internet access across a variety of devices. However, the process of setting up the router requires some support at first because it involves some technical elements that every person finds challenging to comprehend. In order to make it easy for these users to set up their Netgear WNR2000 Router and start using high-speed internet, we have included a simple guide. Continue reading the post to get more about Netgear Router.
Can a wrt54g2 router get internet without any additional devices?
In order for you to have internet, the router should be connected to a cable modem or another switch or wireless router which already have internet access.
Why do you have to place your laptop very near to the wireless router in order to get the signal?
Usually you do not have to do that. Either your wireless adapter is relatively weak your router. If your router has movable antennas see if you can adjust it to get better signal.
Which two components are configured via software in order for a PC to participate in a network environment?
IP address
How do you break password of CISCO router?
Step-by-Step ProcedureFollow these steps in order to recover your password:Attach a terminal or PC with terminal emulation to the console port of the router.Use these terminal settings:9600 baud rateNo parity8 data bits1 stop bitNo flow controlRefer to these documents for information on how to cable and connect a terminal to the console port or the AUX port:Cabling Guide for Console and AUX PortsConnecting a Terminal to the Console Port on Catalyst SwitchesConnect a Terminal to Catalyst 2948G-L3, 4908G-L3, and 4840G Series SwitchesIf you can access the router, type show version at the prompt, and record the configuration register setting. See Example of Password Recovery Procedure in order to view the output of a show version commandNote: The configuration register is usually set to 0x2102 or 0x102. If you can no longer access the router (because of a lost login or TACACS password), you can safely assume that your configuration register is set to 0x2102.Use the power switch in order to turn off the router, and then turn the router back on.Important Notes:In order to simulate this step on a Cisco 6400, pull out and then plug in the Node Route Processor (NRP) or Node Switch Processor (NSP) card.In order to simulate this step on a Cisco 6x00 with NI-2, pull out and then plug in the NI-2 card.Press Break on the terminal keyboard within 60 seconds of power up in order to put the router into ROMMON.If the break sequence does not work, refer to Standard Break Key Sequence Combinations During Password Recovery for other key combinations.Type confreg 0x2142 at the rommon 1> prompt in order to boot from Flash.This step bypasses the startup configuration where the passwords are stored.Type reset at the rommon 2> prompt.The router reboots, but ignores the saved configuration.Type no after each setup question, or press Ctrl-Cin order to skip the initial setup procedure.Type enable at the Router> prompt.You are in enable mode and should see the Router# prompt.Type configure memory or copy startup-config running-config in order to copy the nonvolatile RAM (NVRAM) into memory.Important: Do not type copy running-config startup-config or write. These commands erase your startup configuration.Type show running-config.The show running-config command shows the configuration of the router. In this configuration, the shutdown command appears under all interfaces, which indicates all interfaces are currently shut down. In addition, the passwords (enable password, enable secret, vty, console passwords) are in either an encrypted or unencrypted format. You can reuse unencrypted passwords. You must change encrypted passwords to a new password.Type configure terminal.The hostname(config)# prompt appears.Type enable secret in order to change the enable secret password. For example:hostname(config)#enable secret ciscoIssue the no shutdown command on every interface that you use.If you issue a show ip interface brief command, every interface that you want to use should display up up.Type config-register . Where configuration_register_setting is either the value you recorded in step 2 or 0x2102 . For example:hostname(config)#config-register 0x2102Press Ctrl-z or end in order to leave the configuration mode.The hostname# prompt appears.Type write memory or copy running-config startup-config in order to commit the changes.
What must each host on a TCP IP network be configured with in order to communicate?
IP Address
