0
It means that they start a new friendship or they love each other...Sometimes you see birds do that almost everyday!
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What are the peak and off peak times for mobile phones?
It depends on your carrier. Some start nights at 9 PM, others at 7 PM.
Is 12 volts peak to peak the same as 12 volts ac?
No. 12 volts peak to peak would be 6 in the positive polarity and 6 negative polarity. Simply saying 12 volts AC would be 12 volts in each polarity or 24 volts peak to peak
What is PIV in electronics?
The Peak inverse voltage (PIV) equals the peak value of the input voltage, and the diode must be capable of withstanding this amount of repetition reverse voltage. For the diode in figure, the maximum value of reverse voltage, designated as PIV, occurs at peak of each positive alternation of the input voltage when the diode is forward biased.Peak Inverse Voltage at Positive Half CycleThe Peak Inverse Voltage (PIV) occurs at the peak of each half-cycle of the input voltage when the diode is forward biased . In this circuit, the PIV occurs at the peak of each positive half cycle.
How are Baghdad and golden age linked with each other?
Baghdad was at its highest peak at different times, Golden age means "A city at its highest peak
What is the sexual peak of women?
Women have their sexual peak in their 30's.It depends on the iduvidual, some lose interst at an early age while others are still dreaming in their 70's
What is 'non coincident peak demand' in an electrical system?
Non-Coincident Peak (NCP) is the individual or actual peak demands of each load in an electrical system oftentimes occurring at different hours of the day. It does not necessarily fall during system peak. (This is what i understood about NCP...I gladly welcome corrections)
What is 'non-coincident peak demand' in an electrical system?
Non-Coincident Peak (NCP) is the individual or actual peak demands of each load in an electrical system oftentimes occurring at different hours of the day. It does not necessarily fall during system peak. (This is what i understood about NCP...I gladly welcome corrections)
A generating station is to supply six regions of load whose peak loads are 15000kw ,8000kw?
To determine how much power is needed to fulfill each region's requirement, we first need to know the total peak load of all six regions combined. Total peak load = 15000 kW + 8000 kW + (four more regions' peak loads) Assuming the peak loads of the other four regions are x1, x2, x3, and x4, we can write: Total peak load = 15000 + 8000 + x1 + x2 + x3 + x4 We do not have information about the other four regions, so let's assume they each have a peak load of 10,000 kW: Total peak load = 15000 + 8000 + 10000 + 10000 + 10000 + 10000 = 58000 kW Therefore, the generating station needs to be able to supply a peak power of 58,000 kW to meet the combined peak load of all six regions. To determine how much power is needed to fulfill each region's requirement, we need to divide the total peak load by the number of regions: Power needed per region = Total peak load / Number of regions = 58000 kW / 6 = 9666.67 kW Therefore, each region needs a peak power of approximately 9666.67 kW to fulfill its requirement.
Where is the ridge on a roof?
The highest point, the peak of each gable or hip.
What is a roof ridge beam?
At the peak of the roof where the rafters meet instead of the rafters meeting each other, there is a beam between them that they rest against. It runs the length of the roof peak.
Who named Quandary Peak in Colorado?
Story has it that early miners were perplexed about the identity of rock specimens found on Quandary Peak, thus its name. Or, because the peak was known by several names at one time, you might say others were perplexed about the peak's true name. The matter was settled when the Hayden Atlas listed it as Quandary Peak. This answer is from http://www.mountainclimb.com/store/scripts/geoList.asp?geocategory_id=3. Hope this answer helps!
Has Anyone Ever Climbed The Peak Of Mount Everest?
yes, about 150 people each year.
