0
So they will not get mixed up.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
Exterior electrical service wires should be at least 3 feet away from?
CEC - any window that has the capacity to be opened.The exterior electrical service wires should be at least 3 feet away from any part of any window that is able to be opened.
What properties of copper make it ideal for use in electrical wires and for lining cooking pots?
Following are the properties of copper make it ideal for use in electrical wires and for lining cooking pots:- 1) Ductility 2) Conductivity 3) Low resistance 4) Low cost
Where do the white and black wires go on a 3 prong 120 volt twist lock outlet go?
White is neutral and goes on silver colored screw, black is hot and goes on gold colored screw. The bare or green wire is ground and goes on the green screw.
Proper way to install 3 prong outlet?
Call an electrician. Doing your own electrical work can be dangerous without proper training.For more information please see the answers to the Related Questions shown below.
What colors are electrical wires with number reference?
eletrical wire has 3 specif colour coding. As live wire ,neutral wire,earth wire. 1.live - red 2.neutral-black 3.earth - green. These are the specific color coding of eletrical wire.
How do you direct wire security light from outlet have 3 wires?
A 3 wired electrical fixture includes positive, negative and ground. The ground can be attached to one of the screws in the wall. In the case of the other wires, matching the colors, twisting and capping the wires together will handle the electrical installation.
Why do electrical power tools have only two wires?
The better quality tools all have 3 wires. You are looking at cheaper tools.
Exterior electrical service wires should be at least 3 feet away from?
CEC - any window that has the capacity to be opened.The exterior electrical service wires should be at least 3 feet away from any part of any window that is able to be opened.
How do you repair LDE8414ACE Maytag Dryer?
How do the wires connect on a 3 prong electrical cord on the lde8414ace maytag dryer
What properties of copper make it ideal for use in electrical wires and for lining cooking pots?
Following are the properties of copper make it ideal for use in electrical wires and for lining cooking pots:- 1) Ductility 2) Conductivity 3) Low resistance 4) Low cost
Why does your A4LD transmission not want to shift into overdrive in the afternoon but works in the morning?
There is an electrical cable consisting of 3 wires on the 1992 A4LD. Check to make sure all 3 of these wires are intact, and working. My gray one was snipped on my 1992 A4LD, and after reconnecting it, it worked fine.
How do you splice a ground wire?
Strip the wires back about 3/4" and then using lineman's pliers twist the wires together about 2 turns. Tighten a wire nut securely to the connection. Then tape the splice securely with electrical tape.
Where do the white and black wires go on a 3 prong 120 volt twist lock outlet go?
White is neutral and goes on silver colored screw, black is hot and goes on gold colored screw. The bare or green wire is ground and goes on the green screw.
What is three phase transformer?
A polyphase system is a means of transmitting ac power and it has N live wires with the currents phased by 360/N degrees between them. This arrangement when N is 3 or more needs no neutral wire because the return current for each one of the N wires flows back along all the other live wires. The world-wide standard for electric power transmission uses N=3 and is called 3-phase. Power transmission needs 3 wires when the the three currents are balanced (equal) and 4 wires in other cases where the load currents might not be equal, in which case current flows in the neutral fourth wire.
Where do the wires go on the distributor cap for a 1996 ford ranger 3.0?
electrical --( 3 )---------( 4 ) plug --------( 2 )---------( 6 ) connection ( 1 )---------( 5 ) on the coil pack
If the old block heater cord of a 1988 Honda CRX had two wires and the new end has 3 which colored wires connect the new connector to the old one?
Connect to two wires you have to the the spade connectors and forget the ground connector. The spade connector wires should be black and white. Black to gold and white to silver. If the wires coming from the heater happen to be red and white, then red goes to black. You could buy a simple lamp cord which has only tow wires.
How can you get a neutral from a three phase where their no neutral around?
The normal way is to use a transformer with a 3-wire primary and a 4-wire secondary. In the UK that happens at electricity substations for example where the 11 kV supply comes in on 3 wires and goes out at to users at 240 v with three phase wires and a neutral.
