0
What else can I help you with?
Will the light bulb light up if you connect a wire to it?
No, a light bulb needs a closed circuit with a power source, such as a battery or electrical outlet, in order to light up. Simply connecting a wire to a light bulb without a power source will not allow it to light up.
How is a viper alarm installed into a vehicle?
One can install a Viper alarm system with minimum electrical knowledge. The system has 12 wires. The red and white wire need to be connected to the trunk release wire. The fuse of the red wire needs to be attached to the 'plus' terminal of car battery. The brown wire needs to go to the siren of the car, the yellow wire to the 'plus' of car ignition, the black needs to be attached to the hood as ground, purple wire with 'minus' of dome light, green wire with 'plus' of dome light, blue wire with the sensor pins and orange wire with the hood.
Why is service air bag light on?
When your service air bag light comes on and you have never been in a wreck, this is usually a good indicator of a wire issue. The number one reason for a service air bag light, without a wreck, is that the wire needs to be repaired.
Why is my Lexus license plate light intermittant?
The license plate light on a Lexus may turn on and off if there is a loose wire. Try wiggling the wires around and see if the light goes on and off. If it's not a loose wire then the light bulb may have come loose and needs to be tightened.
What is a light wire?
A light wire is probably a wire with light in it, but to be honest, I haven't really heard of it. lol
Why is your back light out on your 1998 civic?
The most common reason for your back light not to be working is the lightbulb needs to be changed. A broken ground wire can also cause the back light not to work.
Can you change an electrical outlet into a switch for a light?
Sure. For a light you need a fixture to hold the light and the light itself. The light needs to be connected to a voltage supply which you can get from the outlet. In the outlet box you will have a black, white and bare ground wire. Essentially you connect the white and bare wires directly to the light and switch the black wire (hot) through a switch.
How do I wire a light switch to a light?
To wire a light switch to a light, first turn off the power to the circuit. Connect the black wire from the switch to the black wire from the light. Connect the white wire from the switch to the white wire from the light. Finally, connect the ground wire from the switch to the ground wire from the light. Secure all connections with wire nuts and cover with electrical tape. Turn the power back on and test the switch to ensure it is working properly.
How do you wire a motion sensor light?
To wire a motion sensor light, first turn off the power to the circuit. Connect the black wire from the light to the black wire in the electrical box, and the white wire from the light to the white wire in the box. Connect the ground wire from the light to the ground wire in the box. Finally, connect the red wire from the motion sensor to the black wire in the box. Secure all connections with wire nuts and mount the motion sensor light according to the manufacturer's instructions.
Will two batteries and a wire make a light bulb light?
first of all, you need a bulb, a wire, and ONE light bulb. You clip the wire on the battery and touch the wire on the bottom of the light bulb
What is the wiring diagram for a 4 wire light switch?
A 4-wire light switch typically includes a ground wire, a hot wire, a neutral wire, and a traveler wire. The wiring diagram for a 4-wire light switch will show how these wires are connected to the switch terminals to control the light fixture.
How to connect a 3-wire LED light to a 2-wire system?
To connect a 3-wire LED light to a 2-wire system, you can use a resistor to bridge the extra wire. Connect the positive wire of the LED light to the positive wire of the system, and the negative wire of the LED light to the negative wire of the system. Use a resistor to connect the extra wire of the LED light to either the positive or negative wire of the system. This will help regulate the voltage and ensure the LED light functions properly.
