0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Should a 3 wire 250 volt drier be grounded?
Yes, most definitely. Provisions for the ground wire in the dryer receptacle should be used. The feeder cable's ground wire is first grounded to the receptacle's junction box ground screw and then taken to the receptacle's ground terminal. The dryer plug configuration will match up to the dryers four wire plug in cable. When the plug is connected into the dryer receptacle the ground terminals of both devices will match and the ground wire will be continuous from the voltage source at the distribution panel and complete the circuit at the dryer. This low impedance electrical path will conduct any ground fault that could occur at the dryer and trip the feeder breaker of the dryer circuit, there by removing the fault current from the dryer circuit.
Can you hook up a two pole 20 amp breaker to a 30 amp outlet for a dryer?
Probably not. If the appliance has multiple heating levels then you might get away with it. In this scenario you would only be able to use 30 amps of the appliance's 40 amp capacity before the breaker would trip.
You were changing the light bulb in your Kenmore dryer with the power on and hit the hot terminal on the dryer causing a spark the house breaker does not seem to be tripped. model?
It takes a finite amount of time to trip a breaker. The short you caused may not have tripped the breaker. If the dryer is no longer working there may be an internal reset that has tripped.
Can a hair dryer trip a gfi receptacle?
Yes, it can.Our bathroom GFI trips, when my wife uses one particular hair drier.
Can you plug equipment rated for 50A into a 30A circuit?
Yes, with a caveat. The 50A wire and plug is more than heavy enough for the dryer, so there is no problem there. The possible problem is that the dryer is designed to be protected by a 30A breaker. In the event of failure in the dryer, the breaker may not trip as it is oversized. The best solution? Get a small breaker box from a home center and mount a 30A breaker in it. Mount it on the back of the dryer, run the 50A cord into the feed lugs of the box, and connect the dryer feed to the 30A breaker. This way you can plug the dryer into the 50A outlet like you want, and the dryer is protected with a 30A breaker as usual. You can get small breaker boxes or fused disconnects without too much cost. Just make sure the breaker box / disconnect panel is rated to 50A, as you want to feed it off a 50A circuit. As long as the voltage requirement of the dryer matches the voltage of the outlet (which is presumably 240 volts), then yes. The amp rating of the cord and outlet is merely the maximun current (amps) allowed. You're well under that with 24 amps.
When you turn on your new tumble dryer what would cause the electricity to trip in all the sockets?
The dryer plug is probably wired wrong, check where the cord is wired to the dryer first. Unplug the dryer befor starting to remove any screws or panels
Can you plug a 220 dryer in an 220 aircondition plug?
Probably not, the pin configuration of a 30A dryer plug should be different from a 15 or 20A A/C plug. The demand draw of a dryer is higher than that a A/C unit and would trip the 15 or 20A breaker. By putting a bigger breaker on the A/C circuit would not be a good idea either because the wire size to the A/C plug would then be under sized.
What word is to catch your foot and fall?
Trip, tumble or stumble.
To trip or take a false step?
Blunder, stumble, tumble, misstep...
Should a 3 wire 250 volt drier be grounded?
Yes, most definitely. Provisions for the ground wire in the dryer receptacle should be used. The feeder cable's ground wire is first grounded to the receptacle's junction box ground screw and then taken to the receptacle's ground terminal. The dryer plug configuration will match up to the dryers four wire plug in cable. When the plug is connected into the dryer receptacle the ground terminals of both devices will match and the ground wire will be continuous from the voltage source at the distribution panel and complete the circuit at the dryer. This low impedance electrical path will conduct any ground fault that could occur at the dryer and trip the feeder breaker of the dryer circuit, there by removing the fault current from the dryer circuit.
Did my dryer trip the breaker or vice versa when I turned the breaker back on but now the dryer won't work?
The dryer tripped the breaker. Have it repaired. Don't try to use it again. You could cause a fire.
What is an antonym for the word decline?
tumble,trip,fallUh... tumble, trip and fall are SYNONYMS of collapse.Antonyms of collapse could be: rise, build, increase
Can you hook up a two pole 20 amp breaker to a 30 amp outlet for a dryer?
Probably not. If the appliance has multiple heating levels then you might get away with it. In this scenario you would only be able to use 30 amps of the appliance's 40 amp capacity before the breaker would trip.
Why does your main circuit breaker trip when your dryer runs 15 minutes Is it because your vent needs to be cleaned?
Could be but you could also have a weak breaker that will no longer hold the load of your dryer. That is if your talking about your dryer breaker tripping. If your "main breaker" is tripping you have a different problem. Call an electrician in that case. A plugged up dryer shouldn't be tripping your main
You were changing the light bulb in your Kenmore dryer with the power on and hit the hot terminal on the dryer causing a spark the house breaker does not seem to be tripped. model?
It takes a finite amount of time to trip a breaker. The short you caused may not have tripped the breaker. If the dryer is no longer working there may be an internal reset that has tripped.
Can a hair dryer trip a gfi receptacle?
Yes, it can.Our bathroom GFI trips, when my wife uses one particular hair drier.
What happens if you overload plug sockets?
the circuit breaker will trip or fuse will blow to open the circuit.
