answersLogoWhite

0


Want this question answered?

Be notified when an answer is posted

Add your answer:

Earn +20 pts
Q: Why does my peugeot 207 sw estate engine carry on running for a couple of seconds after switching the ignition off?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Why does my peugeot 406 radio lose its signal after 30-40 seconds after switching it on?

because the french are sh*t at electrics


How do you reset immobilizer on peugeot 307 hdi?

If you are having an issue with the immobilizer on a Peugeot 307 HDI, you need to recode your key. To do this put the key into the ignition and turn to the on position, hold the Lock button on the key for 10 seconds, take the key out of the ignition, and then test to see if the car starts after another 10 seconds.


How do you reset the service indicator message on a Mercedes-Benz ML320?

Switch ignition off, press & hold the button to the left of the speedo while switching ignition on. After 10 seconds the new interval will appear in the display accompanied by a beep. Release the button. Switch ignition off.


What does the spanner light mean on the dash of a Peugeot 206?

Switch ignition OFF Press and hold in button between speedo & water temp Switch ignition ON (not start) Keep button in for 10 seconds Display will now read zero and "spanner" symbol gone Relaese button & switch ignition OFF


How do you reset service B indicator on Mercedes clk 200 2001?

On the bottom left of the instrument cluster, is a button marked 0. Switch ignition on and immediately press the button. Switch ignition off. Press and hold the button while switching the ignition on. After 10 seconds, the new interval will appear, accompanied by a beep. Release button. Switch ignition off.


What is the duration of IPW Ignition?

The duration of IPW Ignition is 3600.0 seconds.


How do you program a Peugeot 407 key fob?

If the battery has been out of the key fob for too long the fob loses its program and the car will not start. Peugeot will try to charge £48 for a reprogram but you can get around this by: - 1) Turn on the ignition 2) Hold down the close button for a few seconds 3) Turn off the ignition and remove the key 4) Start the car The above can be found on page 19 or 20 of the 407 user manual


How do you reset the change oil message on your 08 dodge avenger?

the the ignition to on but not the engine running and pres the gass pedal 3 times withing 5 seconds and it will go away


How do you turn off service light on 2006 BMW 525d?

Turn the ignition on but engine not running. Press the tripometer button and hold for ten seconds, a menu will appear showing the same symbols on your I drive. Scroll to the right symbol the press the button for three seconds this will reset the required function. Press the button again for three seconds to confirm changes, then ignition off and all should be OK.


Reset airbag light on Primera P12 series?

(a) Switch OFF the radio & Ignition (b) Turn Ignition ON (Position II) (c) The airbag warning light will stay on for 7 seconds and then switch off - as soon as it does turn OFF the ignition (within 1 second of the light switching off) (d) Wait at least 5 seconds (e) Repeat steps (a) to (c) two more times - this is important to make sure it registers with different modules in the car (f) Turn ON ignition, wait 2 seconds (g) Switch OFF Ignition (Position 0) and wait 1 second (h) Switch ignition back ON. (i) Airbag light should now remain unlit as long as the fault(s) causing are also addressed


How do you program peugeot 107 car key?

Drivers door open Ignition off Switch ignition On then Off Close then Open drivers door twice Switch ignition On then Off Close then Open drivers door twice Close doors and lock using manual knob Switch ignition On then Off Twice Unlock using manual knob Passenger door lock and unlock I waited a few seconds for everything to settle, then everything worked.


Reset warning service light vivaro van?

To reset the engine oil life monitor: The procedure must be completed within 10 seconds after switching on ignition. 1. Switch on the ignition, but do not start the engine, 2. depress accelerator pedal fully and hold in this position, 3. depress foot brake three times consecutively, 4. release accelerator pedal, 5. turn off ignition.