answersLogoWhite

0


Best Answer

Because it's not really -your- Cadillac at all ^_>.

User Avatar

Wiki User

14y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Why does your 97 Cadillac de ville display starting disabled due to theft system?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Starting disabled due to theft system problem?

The theft system problem can make starting the system difficult. It requires professional to first restore the system, enable it before starting it.


How do you disable the anti theft system on a 1991 cadillac deville?

GM uses a Pass-Key 2 anti-theft system during the 1990's which go out quite often. To disable the system turn the ignition key to the on position without starting the car. Wait 30 minutes and turn it off. Repeat these steps 2 more times. After doing this 3 times the system will be disabled and you can start your car.-or-Remove The Anti-Theft Fuse


What does service stability system mean on 2000 Cadillac deville?

i have a 2000 cadillac seville and stability system is on.


How can HyperThreading be disabled on a 2.8 GHz Pentium 4 system?

Hyperthreading has to be enabled or disabled in the BIOS.


How do you disarm the factory alarm system on a 1997 cadillac deville?

Unhook battery cables and then hook back up. Just a temporary fix for an alarm that won't stop. The system can't be completely disarmed unless you want to take a chance on the engine being disabled.


How do you reset the computer system in 1994 Cadillac DeVille after oil change?

Hit INFORMATION button until oil percentage is displayed. Press and hold reset until display reads 100%


How do you Reset anti theft system 1997 Cadillac deville?

How to reset the theft system on 1997 Cadillac Seville


Why is it necessary to choose the appropriate system and sub-system you are assessing before starting an ORM assessment?

This allows TRACS to display information that may be more appropriate to the ORM assessment you are creating.


Starting disabled in 1998 Cadillac el Dorado?

PASS-Key II uses a resistor pellet in the ignition key that is read by the system in your vehicle. If the key resistor matches the code stored in the vehicle system, the vehicle's fuel and starting systems will be enabled. If an incorrect key is used, the vehicle's fuel and starting systems are disabled for three minutes. Additional attempts during this lockout period will not start the car, even with the correct key. If the engine does not start and the STARTING DISABLED REMOVE KEY message is displayed in the Driver Information Center, your key should be checked for damage. Starting may be attempted with an undamaged key immediately. See your dealer or a locksmith for key service. If the STARTING DISABLE REMOVE KEY and WAIT 3 MINUTES messages are displayed, the key should be cleaned. After three minutes, try again. A START CAR message will appear at this time. If the engine still does not start, wait three minutes and try a duplicate key. At this time, fuses should be checked (see "Fuses and Circuit Breakers" in the Index). If the engine does not start with the duplicate key, your vehicle needs service. See your dealer for service. If the THEFT SYSTEM PROBLEM, CAR MAY NOT START message is displayed during vehicle operation, a fault has been detected in the system. This means the PASS-Key II system is disabled and is not protecting the vehicle. The vehicle usually restarts. See your dealer for service. If an ignition key is lost or damaged, see your dealer or a locksmith to have a new key made.


Why is the service stability system message on in your 03 Cadillac cts 03 Cadillac stability control message?

The service stability system message on your 2003 Cadillac CTS usually refers to a problem in your braking system. The problem should be addressed immediately.


Show diagram of 2000 Cadillac catera engine?

diagram of cadillac catera exhaust system


How would you ssh to run xterm on bravo and show the display on the local system?

Use ssh to log into the bravo system. Then, inside the SSH session, export the DISPLAY variable with the IP address and display number of your local system. Then, start up xterm on the bravo system. The results will display on your local system. For this to work, your system must be running in an X windows environment or have an emulator.