0
What else can I help you with?
Difference between MDA and MDL fuse?
A = ceramic, rated at 250V (all values) L = glass, rated at 250V up to 8 amperes(?), but 32V for 9 amperes and above. NOTE: The voltage rating is important! http://www.cooperbussmann.com/pdf/2bd5c594-ca46-48ff-8b97-ab4af4af0569.pdf
Fuse box no power?
Check the fuse which protects the battery circuit. It should be with many amperes on it.
Can you sub a 250 volt 1.5 amp fuse in place of a 125 volt 3 amp fuse?
Yes, you can substitute a 250 volt fuse in place of a 125 volt fuse. You just can't go the other way around. As far as 1.5 amperes in place of 3 amperes, well, you've got a problem there because the fuse will blow at about 1.5 amperes instead of 3 amperes, so the intended load will not be met. All of this, of course, assumes that the physical size of the fuse is the same. Bottom line is never substitute fuses.
Can you use 20 watts or 30 watts in a fuse?
No, watts are a measure of power while fuses are rated in amperes (amps). To determine the fuse rating, you need to calculate the current in amps by dividing the power in watts by the voltage. Then, choose a fuse that is rated equal to or slightly higher than the calculated current in amps.
Can you use 20 Amperes MCB for socket outlet for maintenance purposes?
Only if the sockets are rated for 20 amperes.
Is the F5A FUSE F5AL250V?
Yes, the F5A FUSE F5AL250V refers to a fuse rated for 5 amperes (F5A) and designed for use in circuits with a voltage of up to 250 volts (F5AL250V). The "L" typically indicates that it is a slow-blow or time-delay fuse, which allows for temporary overloads without blowing. Always ensure that the fuse matches the specifications required for your specific application.
Can you power the Pyle PLMPA35 Mini Amplifier 12V 300W with a 4 ohm resistor instead of a 4 ohm fuse?
It is unclear what you as asking about as fuses are rated in Amperes not Ohms. A fuse that measures 4 Ohms would be defective (not good but not fully blown open either).
How many amperes does a car stereo use?
typically 5-10amps. The fuse will tell you
What does p stand for in T5ah250Vp fuse?
In the context of the T5ah250Vp fuse, the "p" typically stands for "Pico," which indicates a specific type of fuse designed for applications requiring precise protection. The "T" denotes the fuse's type, "5" indicates the current rating in amperes (5A), "ah" refers to the time-current characteristics, "250" signifies the voltage rating (250V), and "V" indicates that it is a voltage-rated fuse.
What sould i do i have a 5.17 Volt 2.5a dc wall converter when i make a fused circuit it immediately burns the fuse what should i do?
Check the rating of the fuse (for how many amperes it is designed), and measure or calculate the corresponding current (amperes) that are supposed to go through it.
What is electrical potential of 800va inverter?
It depends on how much current it's putting out. An inverter rated at 800 volt-amperes can deliver 220 volts at 3.636 amperes, or it can deliver 110 volts at 3.727 amperes.
What does it mean when a fuse is rated at 8 Amps?
A fuse rated at 8 Amps means that it is designed to allow a maximum current of 8 amperes to pass through it without blowing. If the current exceeds this threshold, the fuse will melt or break the circuit to prevent damage to electrical components or reduce the risk of fire. This rating is crucial for protecting electrical devices from overloads and ensuring safe operation. Always replace a blown fuse with one of the same rating to maintain proper protection.
