0
Why is it best to use the right size of Philips type screwdriver?
Wiki User
∙ 11y ago
it is best to use the right size of philip screwdriver because this will prevent the screw to be from loosen its thread.
Adolfo Bartoletti
Wiki User
∙ 11y agoThe wrong one won't engage the whole screw head, which increases the risk of stripping out the star pattern when you try to tighten/undo the screw. And w/o the star pattern, tightening or removing the screw becomes quite hard.
Rena Maque
Add your answer:
Earn +20 pts
Where is the engine size marked on the engine?
normal on the front face of the engine or the right hand side of the engine
Calculate wrench size?
To calculate wrench size you measure across the flat surfaces of the nut or bolt, then pick a wrench marked with that size. Be careful, there are metric and SAE nuts and bolts and some wrenches are close but not right. -For instance you should not use a 1/2" wrench on a 12 mm nut. -It may look right, but will round the edges of the nut.
Difference between basic size and nominal size of an assembly?
on the basis of nominal diameter with tolerances is called nominal size, while required size is called basic size
Grain structure of gray cast iron?
The grain structure of gray cast iron falls into 4 main classifications, or types. The most desirable of the four is called Type 'A' wherein the carbon is solidified into flake like crystals, in a random distribution. The size is also classified, in sizes ranging from Size 2 to 7. The best grain structure for general service castings is Type 'A', Size 3 to 5. The smaller the size number indicates the longest flake length, and the excessively long flakes in Size 2 will render the iron somewhat weaker, so the most desirable size is a mixture of 3, 4 and 5. Some applications may call for Type 4, but generally the other Types are undesirable and are the result of defective chemistry or a process defect.
How do you calculate the plate size for a dish end?
Id+kr+2sf=blank size
Why is it best to use the right size of Philip screwdriver?
it is best to use the right size of philip screwdriver because this will prevent the screw to be from loosen its thread.
What size screwdriver do you need to open up a MacBook Pro late 2011?
#00 Philips screwdriver
What size screwdriver do you need to open the Nerf Longshot?
A Miedium size Philips screw driver
Why is it best to use the right size of Philips-type screwdriver?
The wrong one won't engage the whole screw head, which increases the risk of stripping out the star pattern when you try to tighten/undo the screw. And w/o the star pattern, tightening or removing the screw becomes quite hard.
How does a Phillips screwdriver work?
A Phillips screwdriver works by engaging with the cross-shaped Phillips screw head, providing torque to turn and tighten the screw. The design of the driver and screw head allows for increased torque and reduced slipping compared to other screw types, making it easier to drive the screw into place.
Where to get a screwdriver that will work on a dsi?
Hi, you could shop around for a tri-wing screwdriver, many people sell one that's the right size for use on nintendo products.
Is a screw easy to use?
Depends on what head it has, a philips (cross-head) is easier to use than a straight edge head. As long as the screw driver, or drill bit your using is the right size, they aren't bad either way you go (philips or straight) the philips are just easier to keep drivers in.
What size screen does the Philips PET7402/37 offer?
The Philips model PET7402/37 features a 7" Lcd screen for viewing.
What is number 2 screwdriver?
Believe it or not screwdrivers come in sizes. Number 2 is the size of the screwdriver.
What is the negative about a screwdriver?
A screwdriver can damage the slot(s) by deforming the screw-head by either too much force or by using the improper size of screwdriver .
When a screwdriver is used to open a can both the size and dirction of the what change?
Both the size and derection are changed
What do you call different sizes of screwdrivers?
Different sizes of screwdrivers are named based on their size. 1/18 might be the size of a screwdriver. Most of the time they are based on the type of screwdriver, such as Phillips or Flathead.
