0
Any joists which are not straight shoud be positioned with the camber or crown (curved edge) upwards. When loaded these joists will tend to straighten out rather than sag further if laid the other way up!
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
How do you Adjust front wheel camber on Taurus?
Unloosing bolts on rim and remove tire on either side that you want to adjust. Once tire is removedyou will have access to camber. There are two bolts on the camber and you can adjust them both left or right.
Your 2001 Lincoln ls has a negative camber at the rear of the car the right side has a bit more negative camber than the left side can this camber alignment be adjusted evenly?
the LS rear end specs are -1.00 degree on each side, yet aside from using a frame machine to bend the control arms to the perfect degree, they are non- adjustable...another way for ford motor company to steal our money....
What is skateboard camber?
AnswerIt is the curve of the skateboard deck --also referred to as the concave of the deck.this answer is incorrect ^ camber is an upward ark on the board creating more push when you carve, concave is not the same thing as camberCamber is the arch of the board or deck front-to-back, and concave is the arch of the deck side-to-side. A positive 3% camber with a 2% concave would be a deck that is arched up in the middle higher than the front and back ends by 3%, with the edges along the side folded upwards 2%. Some decks are also flat-camber (flat-wood), as well as negative camber, which means the center is arched lower than the front and back. A negative camber deck is also referred to as "rocker" or "rockered"; surfboards are also referred to in this way.
How do you support a straight staircase that is not sitting on a load bearing wall?
You're going to have add columns supporting the bottom and top of the stringers.Or you can double up the joists on either side of the top and thru-bolt them to stringers.You'll have to double or triple up the joists below the stringers (depending on the span of the joists)
What happens to the suspension of a car if you hit a lot of bumps?
you can through out the camber and that causes your tires to wear on one side or the other and it can also do damage to you idler arm and tie rods, which is an important part of your front suspension
How after replacing strut due to accident damage do you adjust rear driver's side wheel or suspension to resolve excess negative camber on a 93 Saturn SC2?
there is a special tool to adjust the rear camber, as far as i know its only available through Snap-On. Most service garages do not carry this tool, but a dealer would.
Can you adjust the camber on a VW Golf?
MK4 applications cannot adjust camber, VW did this on purpose (which is really inconvenient), if you have tire wear, you probably should look into the toe adjustment, its fairly common for the toe to become misaligned which would create uneven tire wear, in some cases adjustment of the toe can be more of the culprit in these situations than camber is.... if however you still wish to adjust camber you'll need a camber plate or kit... (side note, you can tweak a few bolts here and there to so slight camber adjustments, but the results are fairly nonexistent)Answeri know for a fact that the camber cant be adjusted on my 1.4cl as there is no space for the strut to move.it is just a straight bolt through,but as far as i know(im no mechanic)nearly every other golf mk3 will have some kind of adjustment due to the elongated slots.but im told that very few places actually have the laser equipment to do this,and would cost roughly 50-60 quid to do as they need to track and balance again(that's what i was told anayway)hope i have been of some assistance. Purchase the correct camber bolts, or slot the holes in the strut tower. they do not need to be "lasered" to open the slots. A small file or oval grinding wheel works well.
How do you adjust the alignment on a 2002 Passat?
Only the toe is adjustable in the front of any 2002 Passat. Caster and Camber are not adjustable, if one side is off the only thing you can do is shift the entire subframe. There are no adjustments in the rear of a front wheel drive Passat. All wheel drive (4Motion) Passats have toe adjustments in the rear as well. They may have rear camber adjustments.
Can you put 13 inch rims on a car that normally takes 14 inch rims?
if the lug pattern is the same then yes, but its going to effect your camber and will make your tires wear on one side
What are toe in alignment specs for 2005 Chrysler 300?
{| ! align="middle" | FRONT WHEEL ALIGNMENT |} {| ! align="middle" | PREFERRED SETTING |} {| ! align="middle" | ACCEPTABLE RANGE |} CAMBER - LEFT +0.15° -0.50° to +0.80° CAMBER - RIGHT -0.25° -0.90° to +0.04° CROSS-CAMBER (Maximum side-to-side difference) +0.40° -0.10° to +1.15° CASTER - LEFT +9.40° +8.40° to +10.40° CASTER - RIGHT +10.40° +9.40° to +11.40° CROSS-CASTER (Maximum side-to-side difference) -1.00°-1.60° to -0.40° TOE - INDIVIDUAL +0.10° -0.05° to +0.15° TOE - TOTAL* +0.20° -0.10° to +0.30° Maximum side-to-side difference 0.00° 0.06° REAR WHEEL ALIGNMENTPREFERRED SETTINGACCEPTABLE RANGE CAMBER -0.55° -1.20° to +0.10° CROSS-CAMBER (Maximum side-to-side difference) 0.00°-0.80° to +0.80° TOE - INDIVIDUAL LEFT +0.17° +0.02° to +0.32° TOE - INDIVIDUAL RIGHT +0.03° -0.12° to +0.18° THRUST ANGLE +0.07° -0.08° to +0.22° Notes: * TOTAL TOE is the sum of both left and right wheel toe settings. TOTAL TOE must be equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe. Positive toe is toe-in and negative toe is toe-out
Why is BMW 323 pulling to left?
They all follow the camber of the road, so in this country, that is to the left. If you move over to the right hand side at some point (when it is safe to do so, obviously) you will notice it pulls to the right.
How many screws do you need to secure a loft ladder?
3 on each side and two on each end. Make sure you have gone into the joists 1 1/2". Shim the gaps where the screws are and use heavy screws.
