0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How to repair cut underground copper tubing from propane tank?
Copper tubing that is underground must be one complete piece.No connectors,no repairs.All fittings must be above ground.Also all underground copper tubing must be plastic coated to protect it from oxidation.
Does DNA code for the enzymes necessary for the production of lipids and carbohydrates?
No. DNA codes for proteins, but not the lipids and carbohydrates and instruction for their use. All of this originates from diet and from thin air.
What are the safety precautions and techniques when inserting a glass tubing in a rubber stopper?
never attempt to insert glass tubing that has a jagged end, all glass tubing should be fire polished before its inserted into a rubber stopper. Use water or glycerin as a lubricant at the end of the glass tubing before inserting it into the rubber stopper. ask teacher for proper lubricant. Protect hands and fingers by wearing leather gloves or placing a folded cloth between your hands and the tubing. hold it as close as possible to the part it is inserted to the rubber stopper. always point the tubing away from the palm of your hand that holds the stopper. use a twisting motion and push the tubing into the stopper. At the end of the experiment put on leather gloves or place the folded cloth between your hands and the tubing and remover the stoppers from the tubing to keep them from sticking to the glass. if it wont budge, use lubricant.
Is it necessary to masturbulate?
Not at all..........
Can soda bicarbonate remove stains?
Yes it can, depending on the stain, 15-20mins should suffice, allow to absorb the stain, with a damp cloth, dab away until all gone, allow to dry, then vacuum over to remove any dried debris, repeat as necessary.
Burp all the tubing?
Burping lines means to evacuate air from lines
How do you remove a dead mouse from my car air condtioner fan in a car?
To remove a dead mouse from the car air conditioner fan, it will be necessary to remove all the air ducts by the fan or blower. Removing the blower might allow access to the dead mouse without tearing all of the duct work out.
How do you remove a 1998 Nissan Sentra transmission?
To remove a 1998 Nissan Sentra Transmission, you first need to locate all of the bolts. From there, you will remove the bolts. Undo any wiring or tubing that goes into the transmission. From there, it can be taken out.
How do you remove and install a radiator on a 1992 Chevy baretta?
It is simple. Remove all hoses and tubing connections. Remove radiator retaning bolts -screws or other. Take the old one out and put the new radiator in it's place Now reconnect all things disconnected earlier.
Does a central air conditioner dehumidfy the air?
Yes, all air conditioners remove moisture from the air while cooling the air.
Copper Tubing?
form_title= Copper Tubing form_header= Have the supplies you need for all of your home improvement tasks. How much tubing do you need?*= _ [50] Will the tubing be used for liquids?*= () Yes () No Please describe the project in detail.*= _ [50]
How can I change the air in my 4 runner tires?
Not sure why you think you need to? Once the tire is filled you need to check it but not change it. Depending on the tire you may need to add or remove air for the conditions of the road but that is all. Check the side of the tire for the correct inflation pressure and then fill as necessary. If too full then just press the internal release at the fill nozzle to remove some air.
How do you bend copper pipes?
Depends if the copper tubing is annealed or drawn type as not all copper tubing if bendable
96 sunfire powersteering line repaired worked for 10 minutes now no power steering at all?
System has to be "purged" to remove all air from lines System has to be "purged" to remove all air from lines
How do you bleed the coolant system on a 1999 Buick century?
Cold engine. Remove the radiator cap, top it off, start the engine, add coolant as necessary until all air bubbles stop escaping.
Where is the IAT sensor on a 1999 Nissan Altima?
It is important to know the location of all the sensors in a vehicle. The IAT sensor for this vehicle is in the tubing to the air filter box.?æ
What make the air vibrate inside a brass instrument?
The player's lips vibrate together, injecting "puffs" of air into the tubing. This causes the air in the tubing to vibrate. The length of tubing determines the resonance of the air column inside, limiting it wavelengths which are the length of the tubing or integer divisions of that length, i.e., 1/2, 1/3, 1/4, etc. This limitation on the frequencies is what causes the brass instruments to overblow harmonics. When the air in the tubing is only allowing vibration at specific frequencies, the back pressure from those vibrations regulate the vibration of the player's lips, giving him some feedback. With this information, a well-trained player can choose the overtone to play. The tubing for a brass instrument with none of the valves actuated is actually at the shortest length. Each valve adds a short length of tube to the overall length, which lowers the pitches that the tubing will vibrate. This is how notes in between overtones are obtained. Additionally, certain pitches are more easily or precisely obtained from different combinations of valves. To complete the picture, the bell provides impedance matching to the air, which improves the efficiency by which the vibrations in the tubing gets into the air. The bell also makes the length of the tubing slightly ambiguous, contributing to the factors that allow the player to control the pitch by 'lipping'. All of these things combine together to make brass instruments capable of being played very well in tune, in the hands of a well-trained, well-practiced player, or woefully unstable for beginners.
