0
Usually because of moisture, or severe cycles of temperature change.
Wiki User
∙ 8y ago
Add your answer:
Earn +20 pts
What fiber are jeans made of?
denim They are made in general from sturdy cotton warp-faced fibre.
Difference between poplin and cotton voile and cotton cambric?
In common terminology cambric fabric is made up of approximately. equal no. of warp and weft threads irrespective of yarn variety and poplin has almost double the no. of warp threads than the weft threads.
Can you buy a warp skateboard at Walmart?
WANT A GOOD BOARD,> DO NOT SHOP IN WALMART FOR ONE>> TRY ZUMIEZ
Why is wonder board a good underlayment for a floor?
Wonder board is a cement board that is very firm. Unlike wood it doesn't warp or rot. It is especially used as the underlayment for tile floors and shower walls.
How do you make a shade?
First you have to prepare the warp of the material this will give it its density and patern length wise . then it has to be woven, that is placing the material with wire.
How do you make a cloth?
First you have to prepare the warp of the material this will give it its density and patern length wise . then it has to be woven, that is placing the material with wire.
How do you make a shade cloth?
First you have to prepare the warp of the material this will give it its density and patern length wise . then it has to be woven, that is placing the material with wire.
How do you get to the Boss at Silph Co in Pokemon Red?
Once you are at the Silph Company headquarters in Saffron City, the first step is to find the Card Key, which will allow you access the part of the building where the board room is. The Card Key is on the 5th floor. The doors to open with it are on the 3rd floor, in the center left. The warp tile to the far left takes you to a room with another warp tile, and that one takes you to the board room. First you have to battle your rival, and get a Lapras, and then you take the warp tile to the board room, where you battle Giovanni. _____ Giovanni battle: Kangaskhan Lv35, Nidoqueen Lv41, Nidorio Lv37, and Ryhorn Lv37
How do you warp a cricket loom?
you can warp a cricket loom one of two ways: Direct method or Indirect method.Direct Warping (courtesy of freehavenfarmltd on youtube)Indirect Warping (courtesy of various sources)measuring the warpPaulina, weaver from San Juan from aldea on Vimeo.FROM SCHACHT SPINDLE COMPANYIndirect Warping Using a Warping BoardFor this method, a warping board is used to measure the warp. The warp is first measured on the warping board and then brought to the loom for threading.Set up a guide stringStep 1. Determine which pegs of the warping board to use by cutting a piece of string a few inches longer than the length of one warp thread. Use a string that is a different color than your warp yarn.Tie one end of the string to a peg and work back and forth around the pegs until the string runs out. Adjust the starting point until the end of the guide string comes out even at the set of 2 pegs marked x in figure 11.Measure the warpStep 2. Tie the end of the warp yarn to the starting peg. Wind back and forth across the warping board following the guide string until you reach the ending two pegs. Wind a figure-eight around these (figure 12). This is the cross and its purpose is to keep the warp ends in order. Wind back to the beginning peg. You have now measured 2 warp ends. Continue following this path until the total number of warp ends are measured.Figure 10: tie the warp ends to the front apron rodFigure 11: Wind the warp Figure 12: Continue and wind the warp back in the reverse direction Remove the warp from the warping boardStep 3. Secure the cross by tying it loosely with contrasting yarn in five places (figure 13) using overhand knots. Now tie choke ties along the warp at about 18" inch intervals. Tie these tightly with a bow tie. Choke ties keep the warp from tangling. After the warp has been tied, remove it from the warping board. Cut all the loops on the non-cross end and tie the end of the warp bundle in an overhand knot.Thread the heddleStep 4. Wrap the warp around the front beam so that it extends about 10" past the heddle.Step 5. Place the heddle in neutral. Find the center of the heddle and then measure out to one side half the width of your warp. (For example, if your warp is 10" wide, measure out 5" and begin threading at this point.)Step 6. Hold the cross in one hand so that each section is separated (figure 14), and then cut the loops at the end and the five ties holding the cross. Notice that the threads stack up Lincoln-log style. Take the top end and use the heddle hook to thread it through the slot at the outermost edge of your weaving. Take the next thread and thread it through the adjacent hole. Alternately thread slot, hole, slot, hole until all warp ends are threaded.Step 7. Tie groups of about 1" of warp ends in overhand knots across the entire warp. Then tie each group around the back apron rod and secure this knot by tightening it up to the first knot (figure 15).Wind the warp onto the warp beamStep 8. Begin cranking the warp onto the warp beam in a clockwise direction. Remove choke ties as they approach the heddle.Step 9. When the warp has been rolled around the warp beam once, insert heavy paper between the layers of warp to separate them.Step 10. Continue winding on, stopping every so often to pull hard on the warp bundle to tighten the warp on the warp beam.Figure 13: Tie the cross Figure 14: Hold the crossFigure 15: Tie the warp to the back apron rod Step 11. Stop winding when there is about 10" of warp left in front of the heddle.Tie onto the front apron rodTie onto the front apron rod in the same way as for the direct method (step 15, figure 10, page 7).
Can an emp warp metal?
No, it cannot warp metal.
How do you set a warp in minecraft?
/setwarp (name of warp)
What the factor to effect the textile property?
Different fabric woven to different pattern and design, such as plain organization show grain, twill organization show twill pattern, and stain organization show float long line. Organization expect to effect the outside pattern, and it's also effect the textile style and fabric's inner quality etc. such plain fabric strong, stain fabric smoothness and even and having gloss and soft on surface. Woven fabric density is textile weft and warp direction's unit length of the yarn count. Fabric density will effect such as strength/ flexible/ touch/ bone/ breathable and weaving breakage etc. thread count big, textile will be tighten/ stiff/ durable/ strong, thread count small , textile thin/ soft/ breathable great. Same density fabric adopt different yarn, thus fabric actual density will have difference. On the comparison of textile density, must considering the fineness of yarn and density, this is tighten degree, tighten degree is fabric's relative density, is warp(weft) yarn diameter to next two warp(weft) yarn average center distant ratio, using percentage express. More bigger on the ginwave tighten degree, the fabric stiffness bigger, creasing property decrease, anti plane abrasion property increase, anti foldable property decrease, touching harder, and tighten degree small, textile too scarce, and lack of bone. Must point out, textile 's warp tighten degree and warp tighten degree, total tighten degree interaction to each other; total tighten degree to some extent, warp and weft in the same tighten degree, the fabric more tighten, stiffness bigger; however warp bigger than weft , the fabric will be soft and great pendency. Warp and weft different in tighten degree will effect the fabric's ginwave breaking strength. By YULONG tex
