0
To get more fuel-air mixture into a four stroke engine the intake valve stays open to get some added benefit from Newtons third law of motion acting on the fuel-air mixture.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
Ford Laser 1.6 kc valve adjustment?
MUST be done HOT valve stem to rocker: Inlet: .30mm, Exhaust: .30mm camshaft to rocker: Inlet: .19mm, Exhaust: .19mm.... EFI have hydraulic tappits.
How do you replace an AC expansion valve on a 1995 Chevy Camaro Z28?
you have to close the outlet valve with the system running. its called a pump down. when you have that done close the inlet valve. now you should have all your refrigerant in the compressor and accumulator. now you have to sweat out the valve and braze in a new one. next you must suck the open part of the system into a vaccum and have it hold at 19 inches for 24hrs. if it passes then you can reopen your valves and start the system back up. hope it helps
Do Ford Laser 1.6 have adjustable tappets?
Yes. must be done hot. Valve stem to rocker : Inlet .30mm Exhaust .30mm Camshaft to rocker: Inlet .19mm Exhaust .19mm EFI have hydraulic tappits
Why does sub zero water supply to ice maker freeze up?
It could be that your water inlet valve is weeping. This means that a very small amount of water is passing through the valve constantly. Your inlet valve is a triple valve that supplies water to the ice maker and the water in the door, one to filter. The triple valve has three solenoids and three separate diaphragms and flow washers. If one side fails you must change the entire valve. (valve located on back side of unit where water supply connects)
What is the difference between valve and control-valve?
Control valve: Used to modify flow rate in a process control system.It has characterization: linear,equal percentage and quick opening Pressure inlet must be higher than the output pressure Regulator:Diapghram operating valve which controls outlet pressure (reducing application),control inlet pressure (back pressure) or either (differential reducing and differential relief applications
How can I Convert a restaurant U.S. Range oven from gas to propane?
In order to convert a gas range to propane, one must change the inlet valve. There flow rate of the gas must also be adjusted too.
What location must a check valve be placed?
Generally, placed close to the supply discharge of the pump.
Is there anything else you need to do after cleaning cartridge filters and putting everything back together before turning the pump back on after 5 minutes there was still no water moving?
You must purge the air out of the line that sucks the water out of your pool(inlet to pump side).This is usally done by opening a bleeder valve on top of the filter cover. #1 Shut inlet and outlet valve to pool. #2 Clean or change filter and re-install lid. #3 Open pool line valve on inlet to pump side. #4 Open bleeder valve on top of pump until only water comes out,then close bleeder valve. #5 Open pool valve from (pump to pool side) outlet to pool side. #6 Turn pump back on. Running your pump without water for more than a few seconds can damage or burn up your pump.
How do you change the power steering pump on a 2001 Ford Transit?
Remove inlet manifold is a must. Pig of a job for what it is just done mine.
What valve must close before blood will flow from the heart to the various body regions?
The atrioventricular valves close during systole, when the heart pumps blood out to the various body regions. The tricuspid valve closes to prevent backflow from the right ventricle to the right atrium, and the mitral valve closes to prevent backflow from the left ventricle to the left atrium.
What does the PCV valve on a 2003 Mitsubishi galant do and where is it located?
PCV valve is a gauge for gases to pass through to engine. It is located close to oil fuel tank center engine, the gasket cap must be removed to access it.
If your marine toilet has a Y valve what must you do in a non discharge zone?
If your marine toilet has a "Y" valve, and you are in a No DischargeY Zone, you must be certain that the Y valve is secured in a closed position
