0
Why series inductor filter can not be connected to a half wave rectifier?
Wiki User
∙ 10y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What ia series circuit?
A circuit in which elements are connected in series.For example in RLC series circuit resistor,inductor and capacitor are connected in series.
Why inductor use in series capacitor in parallel?
That depends on the type of circuit you are talking about. Sometimes both an inductor and capacitor are both in parallel with each other. This is called a tank circuit. Sometimes they are both used in series. These are both examples of resonant circuits. Sometimes the inductor can be in parallel with an applied voltage and the capacitor in series. This is a form of high pass filter. On the other hand, the inductor can be in series and the capacitor in parallel to for a low pass filter.
How rectifier transformer convert ac to dc energy?
The transformer produces AC at the required voltage, and then one, two or four diodes are connected to it to produce pulsating DC, which is then smoothed to DC by a series inductor, or, in low-power supplies, by a parallel reservoir capacitor. A single diode is called a half wave rectifier because it passes the positive half of the wave and suppresses the negative. Two diodes in conjunction with a centre-tap on the secondary make a full wave rectifier, while four diodes can be connected as a bridge rectifier, which is also full-wave and does not need a centre-tap.
What circumstances is it possible for the rms current drawn from a certain source to have the same magnitude when an inductance is connected in series with a given impedance?
The same as what? when an inductor is connected in series with a resistor and a current passed through them, the voltages across the resistor and inductor are equal when the reactance is equal to the resistance: 2.pi.f.L = R
Why a inductor is used in series before diode instead of resistor?
An inductor will supply better current source.
What is the advantage of capacitor filter over inductor filter?
An inductive filter is in fact an LC circuit in which an inductor is connected in series with the capacitor. This arrangement is also known as a low-pass filter. http://www.answers.com/topic/inductive-filter
What ia series circuit?
A circuit in which elements are connected in series.For example in RLC series circuit resistor,inductor and capacitor are connected in series.
Why inductor use in series capacitor in parallel?
That depends on the type of circuit you are talking about. Sometimes both an inductor and capacitor are both in parallel with each other. This is called a tank circuit. Sometimes they are both used in series. These are both examples of resonant circuits. Sometimes the inductor can be in parallel with an applied voltage and the capacitor in series. This is a form of high pass filter. On the other hand, the inductor can be in series and the capacitor in parallel to for a low pass filter.
In electronics what are series?
When two or more devices such as resistance,inductor are connected one by one or one after other is called series connection.
What is the phase angle of an ohm inductor in series with an ohm resistor connected to a 5 KHz source?
You need to provide values of resistor and inductor etc to find the phase angle.
How rectifier transformer convert ac to dc energy?
The transformer produces AC at the required voltage, and then one, two or four diodes are connected to it to produce pulsating DC, which is then smoothed to DC by a series inductor, or, in low-power supplies, by a parallel reservoir capacitor. A single diode is called a half wave rectifier because it passes the positive half of the wave and suppresses the negative. Two diodes in conjunction with a centre-tap on the secondary make a full wave rectifier, while four diodes can be connected as a bridge rectifier, which is also full-wave and does not need a centre-tap.
What circumstances is it possible for the rms current drawn from a certain source to have the same magnitude when an inductance is connected in series with a given impedance?
The same as what? when an inductor is connected in series with a resistor and a current passed through them, the voltages across the resistor and inductor are equal when the reactance is equal to the resistance: 2.pi.f.L = R
What is the difference between filter and rectifier?
A rectifier is a device that contains diodes to convert an AC supply into DC. The resultant DC voltage has ripple on it at twice the source frequency, or six times the source frequency for a 3-phase rectifier. The subsequent filter is there to filter out the ripple to provide a constant dc voltage. On power supplies the filter is often a series inductor, while on low-power supplies used in electronics the filter is a parallel capacitor. Additional components may be added to give extra pure DC is required.
Which types of filter is independent of load why?
LC filter It is a combination of inductor and capacitor filter. Here an inductor is connected in series and a capacitor is connected in parallel to the load as shown in fig 5.6. As discussed earlier, a series inductor filter will reduce the ripple, when increasing the load current. But in case of a capacitor filter it is reverse that when increasing current the ripple also increases. So a combination of these two filters would make ripple independent of load current. The ripple factor of a chock input filter is given by Since the d.c. resistance of the inductor is very low it allows d.c. current to flow easily through it. The capacitor appears open for d.c. and so all d.c. component passes through it. The capacitor appears open for d.c. and so all d.c components passes through the load resistor RL. Bleeder resistor For optimum functioning, the inductor requires a minimum current to flow through, at all time. When the current falls below this rat, the output will increase sharply and hence the regulation become poor. To keep up the circuit current above this minimum value, a resistor is permanently connected across the filtering capacitor and is called bleeder resistor. This resistor always draws a minimum current even if the external load is removed. It also provides a path for the capacitor to discharge when power supply is turned off.
Which type of filter is independent of load?
LC filter It is a combination of inductor and capacitor filter. Here an inductor is connected in series and a capacitor is connected in parallel to the load as shown in fig 5.6. As discussed earlier, a series inductor filter will reduce the ripple, when increasing the load current. But in case of a capacitor filter it is reverse that when increasing current the ripple also increases. So a combination of these two filters would make ripple independent of load current. The ripple factor of a chock input filter is given by Since the d.c. resistance of the inductor is very low it allows d.c. current to flow easily through it. The capacitor appears open for d.c. and so all d.c. component passes through it. The capacitor appears open for d.c. and so all d.c components passes through the load resistor RL. Bleeder resistor For optimum functioning, the inductor requires a minimum current to flow through, at all time. When the current falls below this rat, the output will increase sharply and hence the regulation become poor. To keep up the circuit current above this minimum value, a resistor is permanently connected across the filtering capacitor and is called bleeder resistor. This resistor always draws a minimum current even if the external load is removed. It also provides a path for the capacitor to discharge when power supply is turned off.
Which type of filter is independent of load why?
LC filter It is a combination of inductor and capacitor filter. Here an inductor is connected in series and a capacitor is connected in parallel to the load as shown in fig 5.6. As discussed earlier, a series inductor filter will reduce the ripple, when increasing the load current. But in case of a capacitor filter it is reverse that when increasing current the ripple also increases. So a combination of these two filters would make ripple independent of load current. The ripple factor of a chock input filter is given by Since the d.c. resistance of the inductor is very low it allows d.c. current to flow easily through it. The capacitor appears open for d.c. and so all d.c. component passes through it. The capacitor appears open for d.c. and so all d.c components passes through the load resistor RL. Bleeder resistor For optimum functioning, the inductor requires a minimum current to flow through, at all time. When the current falls below this rat, the output will increase sharply and hence the regulation become poor. To keep up the circuit current above this minimum value, a resistor is permanently connected across the filtering capacitor and is called bleeder resistor. This resistor always draws a minimum current even if the external load is removed. It also provides a path for the capacitor to discharge when power supply is turned off.
Why a inductor is used in series before diode instead of resistor?
An inductor will supply better current source.
