0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Why ujt called current controlled negative resistance device?
The On/OFF action in UJT is controlled by emitter current
Difference between bjt and ujt?
UJT is the voltage controlled device.in which only one mejority carriers are responsible for current flowing. UJT is one junction transistor and it is three terminal emitter and two base. BJT is the current controlled device. in which both mejority and minority carrier are responsiblefor current flowing. this type of transistor consists of two junction and three terminal these are : emitter , base , collector.
What is unipolar junction transistor?
The bipolar junction transistor is a current operated device with three terminals, emitter, base, and collector. There are two varieties, NPN and PNP. In the NPN variety, if the base is more positive than the emitter and that junction is conducting (greater than typically 0.7 volts), then the current through that junction will control a larger current through the collector emitter junction, when the collecter is also more positive than the emitter and that junction is also conducting. In the PNP variety, the same thing applies, but reverse positive to negative. You can operate in linear mode, where the base current controls the collector current, or you can operate in saturated (switched) mode, where the base current is enough to pass any collector current. This is all dependent on gain, also known as hFe, or beta.
Operation of UJT and block diagram?
Explaine operation of UJT .
How does a ujt relaxation oscillator work?
The operation of the circuit is as follows: C1 charges through R1 until the voltage across it reaches the peak point. The emitter current then rises rapidly, discharging C1 through the base 1 region and R3. The sudden rise of current through R3 produces the voltage pulse. When the current falls to IV the UJT switches off and the cycle is repeated.
Is a UJT a voltage controlled or current controlled device?
voltageCurrent between the two bases of the UJT sets up a voltage gradient in the semiconductor. When the voltage on the emitter of the UJT rises high enough to forward bias the emitter-base junction at the voltage of the interbase gradient where the emitter is located, the UJT "turns on".
Why name of the device is UJT?
UJT means Uni Junction transistor terminals are Emitter,Base1 and Base2.UJT is also called double base diode.UJT operates when the emitter is forward biased.voltage is applied between base1 and base2.If an external voltage is applied at terminal E,no current will flow in to the emitter as long as this applied voltage is less than emitter voltage.When this applied voltage exceeds emitter voltage,current will flow into the emitter and holes get injected from emitter to base1 and are repelled by base2.This results in increase in the region between the junction and the base 1.The increase in conductivity results drop in emitter voltage and increased forward bias of the junction.so emitter current also increases.Then it exhibits a negative resistance.
Can UJT replace BJT?
No. A unijunction transistor (UJT) is entirely different in design and application than a bipolar junction transistor (BJT). The UJT works on the principle of voltage modulation of the effective substrate resistance, while the BJT works on the principle of current amplification from one junction to the other, usually base-emitter to collector-emitter.
Why ujt called current controlled negative resistance device?
The On/OFF action in UJT is controlled by emitter current
Draw the equivalent circuit of UJT?
we can draw an equivalent circuit for UJT USING a DIODE and two resistors.draw a diode in emitter lead ..draw the two resistors in series.As rb1 in base 1 lead ..and rb2 in base 2 lead ..draw rb1 as variable resistor.And put a voltage to the ujt in order to get a positive voltage in base two lead.
Difference between bjt and ujt?
UJT is the voltage controlled device.in which only one mejority carriers are responsible for current flowing. UJT is one junction transistor and it is three terminal emitter and two base. BJT is the current controlled device. in which both mejority and minority carrier are responsiblefor current flowing. this type of transistor consists of two junction and three terminal these are : emitter , base , collector.
Why ujt have this type of symbols?
The symbols in the unijunction transistor show its internal configuration. The emitter (arrow) represents the polarity. When it points in that is a P type transistor. Pointing out is an N type. The the table on its side the table top touching the emitter (arrow). Its' "legs" are the connection to two bases in the device. It does not have a collector. Refer to another Wiki answer for more info.
What is the difference between the UJT and BJT transistors?
UJT (UniJunction Transistor): It is a transistor with only one junction and three terminals: an emitter (E) and two bases (B1 and B2). BJT (Bipolar Junction Transistor): This type of transistor consists of two junctions and three terminals, namely Emitter "E", Base "B" and Collector"C". There are two types of BJT, i) PNP and ii) NPN.
What is the difference between fet and ujt?
The structure of a UJT is quite similar to that of an N-channel JFET. The main difference is that P-type (gate) material surrounds the N-type (channel) material in case of JFET and the gate surface of the JFET is much larger than emitter junction of UJT.
Why a UJT is not a thyristor?
Because to remain in conduction it requires a supply of emitter current. Without a minimum value of emitter current it can't stay in the on position. Most thyristors do not require gate current after they are turned on to remain in conduction
What is inter base resistance in UJT?
The bulk resistance between the two bases, which will be different for different types of UJT. Consult the datasheet for the value.
What is unipolar junction transistor?
The bipolar junction transistor is a current operated device with three terminals, emitter, base, and collector. There are two varieties, NPN and PNP. In the NPN variety, if the base is more positive than the emitter and that junction is conducting (greater than typically 0.7 volts), then the current through that junction will control a larger current through the collector emitter junction, when the collecter is also more positive than the emitter and that junction is also conducting. In the PNP variety, the same thing applies, but reverse positive to negative. You can operate in linear mode, where the base current controls the collector current, or you can operate in saturated (switched) mode, where the base current is enough to pass any collector current. This is all dependent on gain, also known as hFe, or beta.
