0
Why the common mode signal should be rejected in differential amplifier?
Wiki User
∙ 9y ago
because of the coupling between the two transister and absence of capacitance it can amplify both dc and ac
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What is the impact upon the gain when the active load is connected to differential amplifier?
the gain of diffrential amlifier should be more than 2db(6db).so it willincrease.
How much signal voltage should be measured at the bypassed source of a common source amplifier?
the same amount as the drain
Why is gain affected when the bypass capacitor is open?
Applied input signal at the base of the amplifier appears across the emitter resistor (RE) due to inter electrode capacitance so it should be bypassed the emitter resistor (RE) through the bypass capacitor (CB). unbypassed signal will be amplified (common emitter amplifier) and reverse back from the emitter to the collector through the base, amplified signal from the emitter to the collector (common emitter amplifier) is 1800 out of phase to the amplified signal from the base to the collector (common base amplifier), so reduced the gain.
Is odd harmonics present in push pull amplifier?
Odd harmonics are theoretically the only harmonics that are produced by a push-pull amplifier, and even the level of odd harmonics should be very low.
How to Clean Your Bass Amplifier?
Just like any other devices, a bass amplifier needs to be cleaned properly in order to preserve its proper functioning and appearance. Aside from that, a bass amplifier also needs constant cleaning so that dust won’t harbor in it. Generally, cleaning a bass amplifier is not simple, because you need to ensure that its function will not be affected by how you cleaned it. If you own a bass amplifier, here are the steps on how to clean it affectively: • Switch off and unplug the amplifier. It is necessary to unplug the bass amplifier before you clean it. You should also wait until the bass amplifier cools down before cleaning it, especially if you have just used it. • Use a vacuum to clean the outside portion of the cabinet. Generally, bass amplifiers have cabinets with closed back types, compared to guitar amplifiers with open-back cabinets. While you are cleaning the outside portion of the cabinet, you should also observe for some sounds of debris, which could harbor inside and may affect the quality produced by the speakers of your bass amplifier. If your bass amplifier has a vent, then you can tilt the amplifier towards that side and vacuum it in order to remove the debris. • Use a rag made of cotton and wet it with a cleaning solution when you are cleaning the face portion of your amplifier. Do not spray the cleaning solution directly on your amplifier, because it can cause damage. Do not forget to clean under the knobs, because dust may also accumulate there. It helps if you turn the knobs to the extreme left and clean it underneath, then turn the knobs to the extreme right and clean it again. Through this method, you can ensure that everything is properly cleaned. Never use oil-based products in cleaning your amplifier. Only use a cleaning solution that is intended for your amplifier. In addition, it can also help if you will be constantly vacuuming the amplifier because it can also eliminate unusual odors from your amplifier.
What is CMRR of differential amplifier?
CMRR stands for Common Mode Rejection Ratio, and it is a measure of how well the amplifier rejects signals that appear on both leads. The idea is that an amplifier should amplify the (Differential Mode) signal, but not any noise (Common Mode) that might appear on the lines, perhaps due to induction from nearby AC power sources. Since induction will show up on both leads, a high CMRR amplifier will have a greater signal to noise ratio overall
How a amplifier works?
Electricians will tell you that a differential amplifier is a type of electronic amplifier that amplifies the difference between two voltages but does not change the particular voltages.
Do I need a 2-Channel Differential Converter for a Car Amplifier?
Yes, if you want the stereo to perform to it's best, you should purchase one of these.
What is the impact upon the gain when the active load is connected to differential amplifier?
the gain of diffrential amlifier should be more than 2db(6db).so it willincrease.
What do you mean by CCMR of an amplifier?
Did you mean CMRR? If so, it stands for Common Mode Rejection Ratio, and it is a measure of how well the amplifier rejects signals that appear on both leads. The idea is that an amplifier should amplify the (Differential Mode) signal, but not any noise (Common Mode) that might appear on the lines, perhaps due to induction from nearby AC power sources. Since induction will show up on both leads, a high CMRR amplifier will have a greater signal to noise ratio overall.If you meant CCMR, please say that in the discussion or the answer, and we can split the question. I don't recognize CCMR.
How much signal voltage should be measured at the bypassed source of a common source amplifier?
the same amount as the drain
Can one install themselves, or should they seek professional help?
You can install your own amplifier and you will save allot of money. To install an amplifier yourself you should get a How to Guide on how to install an amplifier.
What are the disadvantages of differential amplifier?
A:from a single ended none main concern is offset voltages and current offset and for some latch-up Further explanation: A differential amplifier is actually a very advanced (and good!) amplifier - it (at a minimum) consists of two transistors and biasing schemes, and in a basic form has two inputs and two outputs - one output is inverting, the other is non inverting, thus the two outputs can be used together to provide a 3dB (2 x) gain over using a single output. From a signal to noise ratio, a differential amplifier is also a cut above if implemented correctly and designed well. For the best results, a positive and negative signal should be transmitted to the amplifier. One goes to either input of the amplifier, with the other to the other input. Noise inherently will be added onto both of these lines, but the noise will tend to be in the same direction for both. A differential amplifier has a high "common mode rejection", which means if the same voltage is applied to both inputs, the output will not change (it only amplifies the difference between the inputs). This is why sound boards and a lot of other A/V equipment use differential amplifiers. If these features are not important for your design, then the added complexity of circuitry (usually requiring a positive and negative voltage, multiple transistors, etc.) becomes a disadvantage. Also, if you are just starting out, designing one well may be a bit over your head (a clear disadvantage when you don't know what's going on in the circuit - it becomes very difficult to trouble shoot).
What brand of amplifier should be avoided for lack of quality?
Neuhaus T-2 Amplifier is not so good.
Are there powered car speakers or do you absolutely need an amplifier?
You should get a amplifier if you want good sound quality out of your speakers.
What should you do after being rejected?
die
What type of oil should you be puting in the front differential of a 2002 Dodge Dakota 4x4 front differential oil?
The front differential uses 80w90.
