answersLogoWhite

0


Best Answer

Dont laugh when i ask this but I seen it happen before, Is there gas in the tank?

User Avatar

Wiki User

โˆ™ 2005-10-24 16:59:23
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: Why will a 1990 Buick LeSabre not start after removing the exhaust manifold and installing a new gas tank and fuel pump from a 1990 Chevy Corsica?
Write your answer...
Submit
Related questions

What is bolt torque for lower intake manifold for 97 buick lesabre?

The 1997 Buick LeSabre intake manifold bolt torque specifications is 45 pounds per square inch. The manifold bolts should be torqued in 15 pound intervals.


Where is the EGR valve in a 1997 Buick Lesabre V6 225 and how do you replace it?

Its at the rear of the engine in the intake manifold. Take the 2 bolts off that hold it and clean all of the carbon before installing the new one.


How do you remove and replace fuel pump in 1993 Buick lesabre?

You must remove the fuel tank in order to access the pump. Once you have the tank out, it is just a matter of removing the pump and installing the new one.


WHAT IS code p0108 on a 97 buick lesabre?

Manifold Absolute Pressure/Barometric Pressure Sensor


How do you replace the water heater inlet pipe on the intake manifold on a 3800 buick lesabre?

replace the water heater inlet pipe on the intake manifold on a 3800


How do you charge the battery in the Buick LeSabre without removing it from the car?

Hook it to a battery charger.


What is Buick lesabre trouble code 23?

Manifold ait temperature sensor circuit. Year and model?


Where is coolant temp sensor for 93 Buick lesabre?

The Coolant Temperature Sensor on a 1993 & 1994 Buick LeSabre is located on driver's side of the car under the throttle body, It is screwed into the lower intake manifold. You cannot see it without first removing the throttle body since it is hidden under it. An electronic plug is clipped to the the end of the CTS.


Is there a change in 3800 engine between lesabre and lucerne?

Exactly the same except the Lucerne has the improved metal manifold pipe. I think the 04 and 05 LeSabre also replaced the plastic pipe with metal.


How do you replace the starter on 92 buick lesabre?

The starter on a 92 Buick LeSabre is replaced by disconnecting the battery, removing the retaining bolts, and lowering the starter. The wiring harness can then be disconnected and a new starter installed.


Change struts in 1998 buick lesabre?

Struts on a 1998 Buick LeSabre are changed by jacking the vehicle up, removing the wheel, and unbolting the strut. It can then be pulled from its mounts and a new strut put in place.


Where is the IAT sensor on 93 buick lesabre?

The IAT sensor is located on the intake manifold air cleaning housing or air duct.


98 buick lesabre keeps losing antifreeze an blows white smoke from tailpipe?

Most likely a cracked intake manifold.


Where is the thermostat on a 1992 buick lesabre 6-cylinder And can you change it yourself?

The thermostat on a 1992 LeSabre should be inside of the top radiator hose inlet. You can easily change it by removing the top hose and water inlet.


Where is the EGR valve on a 1993 Buick Lesabre located?

It should be located on the intake manifold by the distibutorless ignition module. On my 92 Lesabre it is located near the plugs at the back of the motor. On my 94 LeSabre it is located on the front/driver's side of the engine. There is a 4-wire connector on the top and it is mounted by two bolts on a flange. About 2" in diameter, 4" high.


1998 buick lesabre license plate bulb replacement?

The license plate bulb on a 1998 Buick LeSabre is replaced by removing the retaining screws and disconnecting the wiring harness. The bulb can then be twisted from the socket and a new bulb installed.


How do you replace side marker bulb on 2002 Buick Lesabre?

The side marker bulbs on a 2002 Buick LeSabre are replaced by removing the retaining screws and disconnecting the wiring harness. The old bulb can then be removed and a new bulb put in its place.


Where is the oxygen sensor located on 1997 buick LeSabre?

In the rear, of the engine, right in the center, on top of the exhaust manifold. Right where the exhaust meets the engine block.


How do you replace window regulator in 2003 Buick LeSabre front driver side?

The way that replace a window regulator in a 2003 Buick LeSabre front drive side is by removing the door panel. Next, disconnect the electrical connector on the regulator and replace.


Where are the oxygen sensors on a 1998 Buick Lesabre?

Usally on the rear manifold rear top of engine. You should be able to see the sensor wire from the brain box going out to it.


How do you change a erg valve in 92 Buick LeSabre?

Most EGR valves are located on the intake manifold with a vacuum line attached. Most are held on with two bolts.


Can you remove the catalytic converter on a 1994 buick lesabre?

The catalytic converter on a 1994 Buick LeSabre can be removed to be replaced. It cannot be removed permanently from the vehicle. Removing the catalytic converter will cause the vehicle to not run properly because there are oxygen sensors attached to it that the car needs. Also, removing the catalytic converter permanently may violate state laws against pollution in some states.


What damage can a leaky intake manifold cause in a 1995 Buick LeSabre?

Serious. On the intake manifold a leak sucking in of air will cause a lean running condition generating excessive heat if the computer is unable to adjust by adding more gas to the mixture.


What are the torque specs for a 1993 Buick lesabre intake manifold?

You did not mention if it was the intake to the cylinder head bolts (1993 buick lesabre 96 in-lbs)..... or ..... the intake upper to lower bolts ( 1993 buick 132 in -lbs) but i hope you will know wich you are looking at since there is a large difference in torqe.


Where is the PCV on a 1998 lesabre?

On almost every engine it is in the side of the valve cover. It is a 2 to 3 inch long plastic part that has a 3/8ths hose that connects to the intake manifold.

Study guides

๐Ÿ““
Create a Study Guide