If you haven't already done this, try holding the trunk release button down for a few seconds on your remote. Toyota set it up this way so that you don't accidentally open the trunk when you mean to lock the doors. There is also a button inside the glovebox that will disable or enable that function. try pressing it and then use the remote.
have you checked to batteries in the remote?
You have to press the unlock button 2 or 3 times to get both doors to unlock no programming needed
Press it once for the driver's door only, and again to unlock the rest of the doors.
if your vehicle is equipped with remote to unlock doors it will work that way, otherwise you must unlock from the inside.
One reason that your remote key will not unlock your Mazda 6 is that a fuse is blown. You may need to replace the batteries in the remote or reprogram the remote. A bad body control module is another reason the remote will not unlock the doors.
Weak batteries inside the remote.
Unlock the doors with the key or with the remote.
It doesn't have one, it opens when you unlock the car doors with your remote.
Unlock the doors with the key, or use the remote.
Scenic fuel cap locks operate with the door system - it's a security thing - if you use the remote to unlock your doors then you will find the fuel flap will open. Of course it will lock when you use the remote to lock the doors.
make sure all doors are locked and windows are up then press and hold start button on remote for 3 secs My remote does not have a single start button. It has 4 buttons; Lock, unlock, open trunk and alarm. I was told I have to hold down a combination of buttons to get the remote start to operate. I forgot what the procedure is. Any ideas?
Unlock the doors with the remote.
Using your entry remote, lock and unlock the doors. This happened to me when I had the battery changed. Subaru tech told me to lock and unlock with the remote and it worked.
While holding the door unlock button on your driver's door, turn the key to ON then OFF, then ON, then OFF. Release the unlock button and the doors should lock/unlock to confirm the PDM is in programming mode. Then hold the door unlock and door unlock buttons on your remote at the same time. After about 15 seconds the doors should lock and unlock to acknowledge that it's picked up the remote. Program all remaining remotes at this time. The system will take up to four remotes.
Either unlock the doors with the remote, or unlock any door with the key.
I have an '04 Highlander and have this capability without any special programming. To unlock the drivers door ONLY, press the remote ONCE. To unlock ALL the doors AND the rear hatch, press the remote TWICE within 3 seconds.
Use your remote to lock and unlock doors it should cancel valet
Unlock the doors or trunk with the key.
LAGUNA II RF RESYNCHRONISING1. Turn Ignition OFF.2. Press the central door locking button for more than 5 seconds. Note: the door should lock then unlock.3. When this happens, 15 seconds is allowed and the immobilizer warning light illuminates.4. Press the remote control once, the doors should lock and unlock.5. Press the second remote control once, the doors should lock and unlock.6. Check the remote control unlocks and locks the doors.LAGUNA II RF RESYNCHRONISING1. Turn Ignition OFF.2. Press the central door locking button for more than 5 seconds. Note: the door should lock then unlock.3. When this happens, 15 seconds is allowed and the immobilizer warning light illuminates.4. Press the remote control once, the doors should lock and unlock.5. Press the second remote control once, the doors should lock and unlock.6. Check the remote control unlocks and locks the doors.
on my 53 vectra you have to unlock all the cr doors ie press remote twice. petrol cap will then open
If the key will not work in the door or the liftgate, you will need to call a locksmith or break a window.
Try taking the battery out of the remote. One of the buttons is probably stuck.
The remote has a radio transmitter built in. The car has a receiver connected to the car locks. The signal from the remote turns on certain circuits in the receiver causing the doors to lock or unlock.
# Sit in car, doors closed. Electronically unlock all doors using the power door unlock switch on the driver's door. # Insert key into ignition switch and turn from OFF to ON 8 times within 10 seconds with the 8th time ending in the ON position. (5 times on some models) # The doors should lock and unlock by themselves to signal programming mode. # Using your remote: lock the doors.