0
Why won't brakes on my 1989 F250 Ford stop the truck I had a new master cylinder rear brakes and cylinders front rotors and brakes?
Wiki User
∙ 15y ago
the air must be bled out... but on this system, it is very hard to do, especially if everything has been changed. you will find air in the r.a.b.s. valve,and there may not be a bleeder valve on it. start by bleeding the master cyl. then go to the r.a.b.s. valve,and bleed valve 1 line at a time. you may have to park truck on an incline to get all the air out. then bleed the wheels, starting w/ r.r, l.r, r.f, & l.f.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
Ford f-250-front brakes not releasingpossibly master cylinder problem?
Master cylinder possible but could also be wheel cylinder problems or warped rotors
Why would you have no brake pressure after replacing brakes rotors calipers and after bleeding the brakes on a 1991 cutlass supreme?
Bleed the master cylinder.& then rebleed the system.
Why would the back brakes on a 1999 Neon heat even though they are new and how do you adjust the parking brake?
there is a possibility that you have a malfunctioning master cylinder. my dodge neon ate up two sets of pads/rotors and drums before we found that the master cylinder was causing the brakes to stick.
Your 1992 Corvette brakes slowly as if the rotors are glazed you have turned the rotors new pads replaced the master cylinder and vacuum booster Any other ideas?
Make sure calipers aren't frozen
How can a person tell if there is abs brakes?
Abs dash light, Abs rings on the cv axles or wheel hubs, hydraulic actuator between the master cylinder and calipers/cylinders. Under extreme braking the pedal should pulsate not to be confused with rotors run out. Hope that helps out.
Changed pads rotors calipers brake hoses bled lines am getting fluid to the brakes there are no leaks brake pedal is stiff when engine is off but it loosens when engine starts no brakes why is this?
the master cylinder is whats bad
Why are the front brakes sticking on your 1992 Ford F250 after you have replaced brake rotors pads calipers brake hoses and master cylinder?
have you tried the proportioning valve. sometimes dirt will get in there and clog the returns.
How much are new brakes for 1997 Ford Taurus?
More detail is needed . Do you mean disc pads, or pads and rotors, or calipers with pads and rotors, or completely new calipers, brakelines and master cylinder. -All of these are viable but different options.-You need to be MUCH more specific in what you want.More detail is needed . Do you mean disc pads, or pads and rotors, or calipers with pads and rotors, or completely new calipers, brakelines and master cylinder. -All of these are viable but different options.-You need to be MUCH more specific in what you want.
What is meant by replace brake cylinder repair?
Brake cylinder repair is that wheel cylinder that holds the oil to keep your brakes running smooth on your back brakes. If you don't repair those you will mess up your rotors and your rims.
You have a 1988 Toyota 4-runner with new hubs and brakes and new rotors and brakes and new wheel cylinders and new master cylinder and you have no brakes and have bled the brakes several times?
If you replaced the master cylinder, you have to bleed it first before bleeding the the lines and wheel circuits... BLEEDING THE MASTER CYLINDER ---"During this process, MAKE SURE THAT THE RESERVOIR DOES'NT RUN DRY OF BRAKE FLUID." 1. Disconnect the lines from the master cylinder and place a pan or rugs under the culinder. 2. Have an assistant depress the brake pedal and hold it down. 3. Block off the outlet ports with your fingers and have the assistant release the pedal. Make a tight seal with your finger, do not allow the cylinder to ingest air while the pedal is released. 4. Repeat steps 2 and 3 three or four times. 5. Connect the brake lines to the master cylinder and top up the fluid reservoir... Next step is bleeding the lines and wheel circuits. Start from the farthest, right R, left R, right F then left F.
How much do drum brakes usually cost?
Yes, drum brakes are expensive. They are those back brakes. If you don't get them repaired they can cause a lot of more money which is destroy your rotors and the wheel cylinders, which are very costly.
How many cylinders does a Mazda RX-8 have?
If a 'cylinder' is a piston, then 0. If a 'cylinder' is a combustion chamber, then 2 (rotors). 1.3L http://www.motorator.com/videos/111
