0
Why would holding a bottle with a metal cap loosen the cap under hot water?
Wiki User
∙ 9y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What metal is under silver plate?
Bronze!! .... ?
What is molten ore?
When purified solid metal is heated under very high temperature it changes to liquid metal .This liquid metal is called molten metal .
Is silver a metal or nonmetal or solid or liquid?
Silver is a metal and under normal circumstances, a solid.
Is xenon a metal or a non metal?
It is an inert gas but it can turn metallic if it is at a temperature under -112°C(-170°F) under a pressure of 150GPa(21753600psi).
Must magnesium metal be also kept under kerosene?
no
How does placing the lid of a jar under hot water help loosen it?
im guessing it makes the metal lid expand and loosen
96 Ford E 250 Van... How do you get the battery loose to replace It has some long steemed screw holding the battery down... How do I loosen it?
look under your fuse box under the hood
How do you loosen pipes from metal plate under sink?
Get a durable, and waterproff wrench, or if you want to be lazy, (like most americans), have a plumber come and do it for you.
How do you remove 98 Audi A6 fuel pump?
In de boot under the carpet. 3 screws holding down a metal plate. Its under this plate
Where is the blower motor resistor in a 1992 Chrysler 5TH Avenue?
IT IS LOCATED UNDER THE WIPER COWLING BEHIND THE WASHER BOTTLE AND HAS TWO SCREWS HOLDING IT IN
How do you remove the windshield wipers from a 2002 Mitsubishi?
There is either a nut under a cap on the arm that is holding it on, or a lock lever that you need to pull or push on under the arm, or it is just stuck, and you might need to spray it with something to loosen it from being rusted.
How do you fill a bottle without getting any air in it?
if your refering to a bottle you fill a giant bowl bigger than the bottle then you put the bottle under the surface then do the same to the cap whilevthe bottle is still under the liquesd and close it with both with the bottle and cap under the surface close it and tada!
How do you remove the windshield washer resivour on a 1981 corvette?
Remove the Vapor Canister under the washer bottle and then unscrew the three screws holding the washer bottle to the car, two on the inside fender well and the third by the upper neck and cap and the pull the bottle down and out. This may be a little tricky but it can be done. Stan
Why does placing a jar under warm running water help loosen the lid?
There are two ways that putting a jar under warm water helps loosen the lid. When heated, materials expand. So the air in the jar could expand, reducing any internal suction. Secondly, the metal cap could expand so as to not have as much friction with the rest of the jar.
Replace 2009 Mazda 6 low beam headlight bulb?
You have to go thru the fender well under the plastic. Best thing to do is remove the tire, loosen the Philips head plastic hold downs and pull them out. Pull down the plastic and you will see a gray cap. Turn it counter clockwise and remove. Unhook the metal clip and loosen the screw holding it down, do not need to remove screw, remove clip and you can remove bulb. I wore latex gloves when handling replacement bulb.
Adjust throttle cable 1991 Nissan Stanza?
Locate the cable under the hood. You find it on the right side of the engine compartment. Loosen the two nuts holding the cable in place. Loosen the lock run. Turn the adjustment nut until the deflection in the middle of the throttle cable is between 1 and 3 millimeters.
When glass stopper in a bottle is stuck it may sometimes be loosened by holding the neck of the bottle under a hot water faucet explain the physical principle responsible for this observed phenomenon?
With a few exceptions (notably melting ice) objects expand when heated. If you run hot water on a bottle neck, the heat is applied directly to the bottle and only indirectly to the stopper inside the bottle, so the bottle heats first, and thereby expands sooner than the stopper does. An expanded bottle will exert less pressure on the stopper.
